Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 783
B2228-SKREEM INTERNAL - RKE RECEIVER
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
Possible Causes
SENTRY KEY REMOTE ENTRY MODULE (SKREEM)
Diagnostic Test
1.
VERIFY THAT THE DTC IS ACTIVE
Turn the ignition on.
NOTE: Before continuing, review and check for the following:
•
Review the repair history of the vehicle.
•
Ensure that the vehicle has the correct PCM and SKREEM installed by verifying the part numbers.
•
With the scan tool, ensure that the PCM and SKREEM are programmed correctly. Compare the PCM VIN
to the SKREEM VIN and ensure the two VINs match.
With the scan tool, clear DTCs.
Perform 5 ignition cycles, leaving the ignition switch on for a minimum of 90 seconds per cycle.
With the scan tool, read DTCs.
Does the DTC reset?
Yes
>> Replace and program the SKREEM in accordance with the Service Information.
NOTE: If this vehicle is equipped with a Steering Column Lock Module, it must be replaced along with the
SKREEM.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
No
>> The DTC is not active at this time. Test complete.
8Q - 100
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
LX
B2229-SKREEM INTERNAL - SKIM IMMOBILIZER
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on.
Possible Causes
SENTRY KEY REMOTE ENTRY MODULE (SKREEM)
Diagnostic Test
1.
VERIFY THAT THE DTC IS ACTIVE
Turn the ignition on.
NOTE: Before continuing, review and check for the following:
•
Review the repair history of the vehicle.
•
Ensure that the vehicle has the correct PCM and SKREEM installed by verifying the part numbers.
•
With the scan tool, ensure that the PCM and SKREEM are programmed correctly. Compare the PCM VIN
to the SKREEM VIN and ensure the two VINs match.
With the scan tool, clear DTCs.
Perform 5 ignition cycles, leaving the ignition switch on for a minimum of 90 seconds per cycle.
With the scan tool, read DTCs.
Does the DTC reset?
Yes
>> Replace and program the SKREEM in accordance with the Service Information.
NOTE: If this vehicle is equipped with a Steering Column Lock Module, it must be replaced along with the
SKREEM.
Perform SKREEM VERIFICATION TEST. (Refer to 8 - ELECTRICAL/VEHICLE THEFT SECURITY -
STANDARD PROCEDURE)
No
>> The DTC is not active at this time. Test complete.
LX
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 101
B222A-VEHICLE LINE MISMATCH
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Anytime the ignition key is in the ON position.
•
Set Condition:
If the Intrusion Transceiver Module is not configured.
Possible Causes
INTRUSION TRANSCEIVER MODULE CONFIGURATION
Diagnostic Test
1.
CONFIGURE THE INTRUSION TRANSCEIVER MODULE
Using the scan tool under miscellaneous functions perform the initialization procedure for the Intrusion Transceiver
Module.
With the scan tool, clear DTC(s).
Turn the ignition off and remove the key from the ignition.
Lock and close all doors to allow the VTSS to go from pre-arm to armed status and wait one minute.
Disarm the VTSS.
Using the scan tool, read DTC(s).
Does the DTC reset?
Yes
>> Replace the Intrusion Transceiver Module in accordance with the Service Information.
Perform BODY VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
No
>> Test complete.
Perform BODY VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
8Q - 102
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
LX
B223C-INTRUSION TRANSCEIVER MODULE INTERNAL
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
Ignition on.
•
Set Condition:
Internal Intrusion Transceiver Module test failed.
Possible Causes
INTRUSION TRANSCEIVER MODULE
Diagnostic Test
1.
DETERMINING IF DTC IS CURRENT
With a scan tool, read and record DTC(s).
With the scan tool, clear DTC(s).
Turn the ignition off and remove the key from the ignition.
Lock and close all doors to allow the VTSS to go from pre-arm to armed status and wait one minute.
Disarm the VTSS.
Using the scan tool, read DTC(s).
Does the DTC reset?
Yes
>> Replace the Intrusion Transceiver Module in accordance with the Service Information.
Perform BODY VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
No
>> DTC is not active at this time. Test complete.
Perform BODY VERIFICATION TEST – VER 1 (Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL
MODULES - STANDARD PROCEDURE)
LX
VEHICLE THEFT SECURITY - ELECTRICAL DIAGNOSTICS
8Q - 103
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст