Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2116
18. Apply adhesive backed nylon mesh (dry wall tape)
over gaps around patch.
19. Mix enough adhesive to cover the entire patch
area.
20. Apply adhesive over the mesh around patch, and
smooth epoxy with a wide spreader to reduce fin-
ish grinding. Use two to three layers of mesh and
adhesive to create a stronger repair.
PATCHED PANEL SURFACING
After patch panel is installed, the patch area can be finished using the same methods as finishing other types of
body panels. If mesh material is exposed in the patched area, grind surface down, and apply a coat of high quality
rigid plastic body filler. Prime, block sand, and paint as required.
SPECIFICATIONS
BODY LUBRICATION
LUBRICATION REQUIREMENTS
Body mechanisms and linkages should be inspected, cleaned, and lubricated, as required, to maintain ease of oper-
ation and to provide protection against rust and wear. When performing other under hood services, the hood latch
release mechanism and safety catch should be inspected, cleaned, and lubricated. During the winter season, exter-
nal door lock cylinders should be lubricated to assure proper operation when exposed to water and ice.
Prior to the application of any lubricant, the parts concerned should be wiped clean to remove dust and grit. If
necessary, a suitable solvent can be used to clean the item to be lubricated. After lubricating a component, any
excess oil or grease should be removed.
23 - 12
BODY
LX
LUBRICANT APPLICATION
DOOR LOCK CYLINDERS
1. Apply a small amount of lubricant directly into the lock cylinder.
2. Apply a small amount of lubricant to the key.
3. Insert key into lock cylinder and cycle the mechanism from the locked to the unlocked position.
NOTE: Do not add more lubricant.
4. Cycle the lock cylinder mechanism several times to allow the lubricant to flow throughout the cylinder.
5. Wipe all lubricant from exterior of lock cylinder and key.
ALL OTHER BODY MECHANISMS
1. Clean component as described above.
2. Apply specified lubricant to all pivoting and sliding contact areas of component.
LUBRICANT USAGE
ENGINE OIL
•
Door Hinges – Hinge Pin and Pivot Contact Areas
•
Hood Hinges – Pivot Points
•
Liftgate Hinges
MOPAR
T
SPRAY WHITE LUBE OR EQUIVALENT
•
Door Check Straps
•
Liftgate Latches
•
Liftgate Prop Pivots
•
Ash Receiver
•
Fuel Filler Door Remote Control Latch Mechanism
•
Parking Brake Mechanism
•
Sliding Seat Tracks
•
Liftgate Latch
MOPAR
T
Multipurpose GREASE OR EQUIVALENT
•
All Other Hood Mechanisms
MOPAR
T
LOCK CYLINDER LUBRICANT OR EQUIVALENT
•
Door Lock Cylinders
•
Liftgate Lock Cylinder
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Front Console Shifter Bezel
3
—
23
Front Console to Instrument Panel
3
—
23
Front Door Bottom Pull Bracket to Window Regulator Rear Rail
11
—
100
Front Door Latch to Outer Latch Face
12
—
108
Front Door Bottom Pull Cup Bracket to Inside Front Door
11
—
100
Front Door Glass Clamps
10
—
90
Front Door Exterior Handle to Door
5
—
44
Front seat track to floor pan bolts
61
45
—
LX
BODY
23 - 13
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Front seat inboard pivot bolt
40
30
—
Front seat recliner to seat cushion frame
12
9
—
Front seat track to cushion frame bolt
12
9
—
Front seat back
40
30
—
Front seat back to seat cushion
30
22
—
Front seat arm rest - 60/40
12
9
—
Front arm rest - 50/50 split
25
18
—
Front seat back recliner to seat back
12
9
—
Front seat belt buckle anchor nut
40
29
—
Front seat belt retractor bolt
38
28
—
Front seat belt buckle anchor bolt
40
29
—
Front door hinge to hinge pillar bolt
28
21
—
Front Door Hinge to Bracket to Outside the Lower A-Pillar
30
—
22
Front door hinge to door nuts and bolt
28
21
—
Front door latch striker
28
20
—
Front seat rear outboard seat track to floor pan bolts
28
20
—
Front strut tower to tower brace bolts
38
28
—
Decklid latch striker
22
16
—
Decklid Spoiler SRT 8
6
4.4
—
Door hinge bolt and nut
28
21
—
Door hinge double ended stud
14
—
120
Headlamp Mounting Crossmember
28
—
21
Hood latch release cable handle to the cowl side
2.3 to 3.4
—
20 to 30
Hood latch to crossmember
22.6 to
33.9
—
200 to
300
Hood hinges
22.6 to
33.9
—
200 to
300
Horn to Crossmember
28
—
21
Instrument Panel Side Support Bolts
27
—
20
Interior Remote Handle to Inside Door
2
—
16
Instrument Panel Fence Bolts
8
—
70
Instrument Panel Bottom Bolts
6
—
55
Rear Child Tether anchor
20
15
—
Radiator Mounting Bracket to Headlamp Mounting Crossmember
28
—
21
Rear door glass to regulator bolt
11
—
105
Rear seat arm rest to seat back with ski pass
5
—
46
Rear seat back and belts to floor
44
32
—
Rear seat back 40 section to collar section
60
44
—
Rear seat back 60 section
16
12
—
Rear seat back collar assembly
60
44
—
Rear door hinge to B-pillar bolt
28
20
—
Rear door hinge to door bolt
28
20
—
Rear door latch striker
28
20
—
Sunroof module to roof panel
11
—
97
23 - 14
BODY
LX
SPECIAL TOOLS
BODY
Trim Stick C-4755
TORX BIT SET C-4794-B
REMOVER, MOLDINGS C-4829-A
Outer Belt Molding Remover - 9093
LX
BODY
23 - 15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст