Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1898
P2638-TORQUE MANAGEMENT FEEDBACK SIGNAL PERFORMANCE
For a complete wiring diagram Refer to Section 8W
21 - 126
AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS
LX
Theory of Operation
The Transmission Control Module (TCM) requests torque reductions over the CAN bus during a transmission shift to
improve shift quality. The TCM verifies that the PCM / ECM has performed the requested torque reduction by mon-
itoring the response to the request. If the response is not within a specified tolerance, the TCM increments a
counter, and if this counter reaches a threshold, the DTC sets.
•
When Monitored:
Engine intervention active for at least 20 ms, no engine torque errors, engine torque demand is greater than 0.
•
Set Condition:
Torque Reduction acknowledge bit - not set, no shift aborts, the error flag Torque Reduction Acknowledge is
not set, Powertrain controller not supporting torque requests.
Possible Causes
CAN BUS CIRCUIT DTC PRESENT
TRANSMISSION CONTROL MODULE
POWERTRAIN / ENGINE CONTROL MODULE
Always perform the NAG1 Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 21 -
TRANSMISSION/TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)
Diagnostic Test
1.
CHECK FOR ENGINE DTC PRESENT
With the scan tool, check engine DTCs.
Are there any engine DTCs present?
Yes
>> Refer to the 9 - ENGINE ELECTRICAL DIAGNOSTICS and diagnose the appropriate symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)
No
>> Go To 2
2.
CHECK FOR CAN BUS DTCS
With the scan tool, check for any CAN bus DTCs or a sign of a CAN bus failure.
Are there any CAN bus DTCs present in any module other than the TCM or an overall indication of a
CAN bus communication problem?
Yes
>> This is an indication of a CAN bus communication problem. Depending on the DTC, either refer to the
module reporting the DTC and perform diagnostics for the appropriate symptom or refer to 8 - ELEC-
TRICAL - ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS and perform the appro-
priate symptom.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)
No
>> Go To 3
LX
AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS
21 - 127
3.
CHECK IF DTC RESETS
Turn the ignition off to the lock position.
Replace and program the Powertrain Control Module per the Service Information. Refer to 8 - ELECTRICAL/ELEC-
TRONIC CONTROL MODULES/POWERTRAIN CONTROL MODULE for the appropriate service procedure.
With the scan tool, record the Environmental Data and erase Transmission DTCs.
NOTE: If the TCM detects and stores a DTC, the TCM also stores the vehicles operating conditions under
which the DTC originally set and is located in scan tool under Environmental Data. Before erasing any
stored DTCs, record any available data to assist in duplicating the conditions in which the DTC originally
set.
Using the Environmental Data recorded earlier, test drive the vehicle while trying to duplicate the conditions in which
the DTC originally set.
With the scan tool, read Transmission DTCs.
Did the DTC P2638-TORQUE MANAGEMENT FEEDBACK SIGNAL PERFORMANCE reset?
Yes
>> Using the schematics as a guide, check the Transmission Control Module (TCM) terminals for corrosion,
damage, or terminal push out. Pay particular attention to all power and ground circuits. If no problems
are found, replace the TCM per the Service Information. (Refer to 8 - ELECTRICAL/ELECTRONIC
CONTROL MODULES/TRANSMISSION CONTROL MODULE - DESCRIPTION)
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)
No
>> Test Complete.
Perform NAG1 TRANSMISSION VERIFICATION TEST - VER 1. (Refer to 21 - TRANSMISSION/
TRANSAXLE/AUTOMATIC - NAG1 - STANDARD PROCEDURE)
21 - 128
AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS
LX
P2767-INPUT SPEED SENSOR 2 CIRCUIT NO SIGNAL
For a complete wiring diagram Refer to Section 8W
LX
AUTOMATIC TRANSMISSION NAG1 - ELECTRICAL DIAGNOSTICS
21 - 129
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст