Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 474
INSTALLATION
2.7L
1. To avoid cross threading, start the spark plug into
the cylinder head by hand.
2. Tighten spark plugs. Tighten to 17 N·m (12.5 ft.
lbs.).
3. Install ignition coil assembly onto spark plug.
4. Hand tighten coil screws.
5. Tighten ignition coil screws to 6.7 N·m (60 in. lbs.).
6. Connect and lock the electrical connector.
7. Install the intake manifold, (Refer to 9 - ENGINE/
MANIFOLDS/INTAKE
MANIFOLD
-
INSTALLA-
TION)
8. Connect the negative battery cable.
3.5L
1. To avoid cross threading, start the spark plug into
the cylinder head by hand.
2. Tighten spark plugs. Tighten to 28 N·m (20 ft. lbs.).
3. Install ignition coil assembly onto spark plug.
4. Hand tighten coil screws.
5. Tighten ignition coil screws to 6.7 N·m (60 in. lbs.).
6. Connect and lock the electrical connector.
7. Install the intake manifold, (Refer to 9 - ENGINE/
MANIFOLDS/INTAKE
MANIFOLD
-
INSTALLA-
TION)
8. Connect the negative battery cable.
5.7L/6.1L
Special care should be taken when installing spark plugs into the cylinder head spark plug wells. Be sure the plugs
do not drop into the plug wells as electrodes can be damaged.
Always tighten spark plugs to the specified torque. Over tightening can cause distortion resulting in a change in the
spark plug gap or a cracked porcelain insulator.
1. Start the spark plug into the cylinder head by hand to avoid cross threading.
2. Tighten spark plugs. Refer to torque specifications.
3. Before installing ignition coil(s), check condition of coil o-ring and replace as necessary. To aid in coil installation,
apply silicone to coil o-ring.
4. Install ignition coil(s). Refer to Ignition Coil Removal/Installation.
8I - 74
IGNITION SYSTEM - SERVICE INFORMATION
LX
INSTRUMENT CLUSTER
TABLE OF CONTENTS
page
page
INSTRUMENT CLUSTER - ELECTRICAL
DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . 45
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
TABLE OF CONTENTS
page
page
INSTRUMENT CLUSTER - ELECTRICAL
DIAGNOSTICS
DIAGNOSIS AND TESTING
B1200-AIRBAG WARNING INDICATOR
CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
B1202-AIRBAG WARNING INDICATOR
CIRCUIT OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
B1225-REAR WIPER INDICATOR CONTROL
CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
B1226-REAR WIPER INDICATOR CONTROL
CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
B160A-PANEL DIMMER INPUT CIRCUIT
LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
B160B-PANEL DIMMER INPUT CIRCUIT
HIGH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
B1613-PANEL ILLUMINATION CONTROL
CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
B1614-PANEL ILLUMINATION CONTROL
CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
B1694-ACCESSORY DIMMING CONTROL
CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
B1695-ACCESSORY DIMMING CONTROL
CIRCUIT OPEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
B2107-IGNITION SWITCH SENSE INPUT
CIRCUIT/PERFORMANCE . . . . . . . . . . . . . . . . . . 28
B2108-IGNITION SWITCH SENSE INPUT
CIRCUIT LOW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
B2109-IGNITION SWITCH SENSE INPUT
CIRCUIT HIGH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
FRONT CONTROL MODULE . . . . . . . . . . . . . . . . 43
OCCUPANT RESTRAINT CONTROLLER . . . . . 43
PARKING ASSIST CONTROL MODULE . . . . . . 43
U0164-LOST COMMUNICATION WITH HVAC
CONTROL MODULE . . . . . . . . . . . . . . . . . . . . . . . 43
RADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
SDARS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
HANDS FREE PHONE MODULE . . . . . . . . . . . . 43
HEATED SEAT CONTROL MODULE . . . . . . . . . 44
MEMORY SEAT CONTROL MODULE . . . . . . . . 44
SCCM-CAN-B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
LX
INSTRUMENT CLUSTER
8J - 1
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
DIAGNOSIS AND TESTING
8J - 2
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
LX
B1200-AIRBAG WARNING INDICATOR CIRCUIT LOW
For a complete wiring diagram Refer to Section 8W.
•
When Monitored:
With the ignition on and when requested to turn on by the Occupant Restraint Controller (ORC).
•
Set Condition:
The Instrument Cluster software detects the voltage across the Airbag Lamp is below 0.5 volts when ON.
Possible Causes
INSTRUMENT CLUSTER
Diagnostic Test
1.
CHECK FOR ACTIVE DTC
NOTE: The Instrument Cluster performs internal tests on the Airbag Lamp during each ignition cycle.
With the scan tool, erase DTCs.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Wait for the Instrument Cluster to perform the bulb check.
With the scan tool, read DTCs.
Is the DTC active?
Yes
>> Replace and program the Instrument Cluster in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
No
>> Test complete.
LX
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
8J - 3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст