Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1788
CAUTION: Do not use spray (carb) cleaners on
any part of the throttle body. Do not apply silicone
lubricants to any part of the throttle body.
3. Install throttle body to intake manifold by position-
ing throttle body to manifold alignment pins.
4. Install and tighten four mounting bolts (2). Refer to
Torque Specifications.
5. Install electrical connector (3).
6. Install rubber air hose to throttle body.
7. A Scan Tool may be used to learn electrical param-
eters. Go to the Miscellaneous menu, and then
select ETC Relearn. If the relearn is not preformed,
a Diagnostic Trouble Code (DTC) will be set. If
necessary, use a scan tool to erase any Diagnostic
Trouble Codes (DTC’s) from PCM.
6.1L
1. Clean and check condition of throttle body-to-intake
manifold o-ring (2).
2. Clean mating surfaces of throttle body and intake
manifold (1).
14 - 226
FUEL INJECTION
LX
CAUTION: Do not use spray (carb) cleaners on
any part of the throttle body. Do not apply silicone
lubricants to any part of the throttle body.
3. Install throttle body to intake manifold by position-
ing throttle body to manifold alignment pins.
4. Install and tighten four mounting bolts (3). Refer to
Torque Specifications.
5. Install electrical connector (2). To lock connector,
slide the red colored tab towards throttle body. Pull
firmly on connector to verify a good lock.
6. Install rubber air hose to throttle body.
7. A Scan Tool may be used to learn electrical param-
eters. Go to the Miscellaneous menu, and then
select ETC Relearn. If the relearn is not preformed,
a Diagnostic Trouble Code (DTC) will be set. If
necessary, use a scan tool to erase any Diagnostic
Trouble Codes (DTC’s) from PCM.
LX
FUEL INJECTION
14 - 227
FUEL INJECTION - DIESEL
TABLE OF CONTENTS
page
page
FUEL INJECTION - DIESEL
TORQUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
3.0L DIESEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 229
ACTUATOR-INTAKE PORT SWIRL
INJECTOR-FUEL
SENSOR-ACCELERATOR PEDAL POSITION
SENSOR-CAMSHAFT POSITION
SENSOR-CRANKSHAFT POSITION
SENSOR-FUEL PRESSURE
SENSOR-MASS AIR FLOW (MAF)
SENSOR-BOOST PRESSURE
. . . . . . . . . . . . . . . . . . . . . 247
SENSOR-INTAKE AIR TEMPERATURE
SENSOR-FUEL TEMPERATURE
SOLENOID-FUEL PRESSURE
SOLENOID - FUEL QUANTITY
RAIL-FUEL
14 - 228
FUEL INJECTION - DIESEL
LX
FUEL INJECTION - DIESEL
SPECIFICATIONS
TORQUE
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Bolt, Intake Swirl Port
Actuator
12
-
106
Bolt, Fuel Injector
Tensioning Claw
7+180°
-
62+180°
Nut, High Pressure Fuel
Line
27
20
-
Bolt, Camshaft Position
Sensor
8
-
71
Bolt, Crankshaft Position
Sensor
9
-
80
Bolt, Fuel Pressure
Sensor
22
-
194
Bolt, Boost Pressure
Sensor
9
-
80
Sensor, Fuel Temperature
25
18
-
Bolt, Fuel Rail
11
-
97
Nut, High Pressure Line to
Fuel Rail
33
24
-
Nut, High Pressure Fuel
Rail Transfer Pipe
27
19
-
Nut, High Pressure Line
from Injector to Fuel Rail
27
20
-
Bolt, Wiring Harness Hold
Down
11
-
97
SPECIAL TOOLS
3.0L DIESEL
Pliers, Fuel Line - 9539
LX
FUEL INJECTION - DIESEL
14 - 229
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст