Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1932
AUTOMATIC TRANSMISSION NAG1 - SERVICE
INFORMATION
TABLE OF CONTENTS
page
page
AUTOMATIC TRANSMISSION NAG1 - SERVICE
OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
. . . . . . . . . . . . . . . . . . . . . . . . . 302
TRANSMISSION - NAG1 . . . . . . . . . . . . . . . . . . . 349
MECHANISM-BRAKE TRANSMISSION SHIFT
ADJUSTMENTS - BRAKE TRANSMISSION
. . . . . . . . . . . . . . . . . . . . . . . 353
UNIT-ELECTROHYDRAULIC CONTROL
FLUID AND FILTER
CLUTCH-FREEWHEELING
CABLE-GEARSHIFT
GEARSHIFT CABLE . . . . . . . . . . . . . . . . . . . . . . . . 387
CLUTCHES-HOLDING
B1-HOLDING CLUTCH
B2-HOLDING CLUTCH
CLUTCHES-INPUT
K1-INPUT CLUTCH
K2-INPUT CLUTCH
K3-INPUT CLUTCH
SENSORS-INPUT SPEED
PUMP-OIL
BEARING-OUTPUT SHAFT
SEAL-OUTPUT SHAFT
CABLE-PARK LOCK
GEARTRAIN-PLANETARY
21 - 262
AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION
LX
MECHANISM-SHIFT
SOLENOID
CONTACT-TEMPERATURE SENSOR/PARK-
NEUTRAL
DESCRIPTION
PARK/NEUTRAL CONTACT . . . . . . . . . . . . . . . . . 450
TRANSMISSION TEMPERATURE SENSOR . . 450
PARK/NEUTRAL CONTACT . . . . . . . . . . . . . . . . . 451
TRANSMISSION TEMPERATURE SENSOR . . 451
CONVERTER-TORQUE
SEAL-TORQUE CONVERTER HUB
LX
AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION
21 - 263
AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION
DESCRIPTION
The NAG1 automatic transmission is an electronically controlled 5-speed transmission with a lock-up clutch in the
torque converter. The ratios for the gear stages are obtained by 3 planetary gear sets. Fifth gear is designed as an
overdrive with a high-speed ratio.
NAG1 identifies a family of transmissions and means “N”ew “A”utomatic “G”earbox, generation 1. Various marketing
names are associated with the NAG1 family of transmissions, depending on the transmisson variation being used in
a specific vehicle. Some examples of the marketing names are: W5A300, W5A380, and W5A580. The marketing
name can be interpreted as follows:
•
W = A transmission using a hydraulic torque converter.
•
5 = 5 forward gears.
•
A = Automatic Transmission.
•
580 = Maximum input torque capacity in Newton meters.
The gears are actuated electronically/hydraulically. The gears are shifted by means of an appropriate combination of
three multi-disc holding clutches, three multi-disc driving clutches, and two freewheeling clutches.
Electronic transmission control enables precise adaptation of pressures to the respective operating conditions and to
the engine output during the shift phase which results in a significant improvement in shift quality.
Furthermore, it offers the advantage of a flexible adaptation to various vehicle and engines.
Basically, the automatic transmission with electronic control offers the following advantages:
NAG1 Automatic Transmission
1 - TORQUE CONVERTER
11 - PARKING LOCK GEAR
2 - OIL PUMP
12 - INTERMEDIATE SHAFT
3 - DRIVESHAFT
13 - FREEWHEEL F2
4 - MULTI-DISC HOLDING CLUTCH B1
14 - REAR PLANETARY GEAR SET
5 - DRIVING CLUTCH K1
15 - CENTER PLANETARY GEAR SET
6 - DRIVING CLUTCH K2
16 - ELECTROHYDRAULIC CONTROL UNIT
7 - MULTI-DISC HOLDING CLUTCH B3
17 - FRONT PLANETARY GEAR SET
8 - DRIVING CLUTCH K3
18 - FREEWHEEL F1
9 - MULTI-DISC HOLDING CLUTCH B2
19 - STATOR SHAFT
10 - OUTPUT SHAFT
20 - TORQUE CONVERTER LOCK-UP CLUTCH
21 - 264
AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION
LX
•
Reduces fuel consumption.
•
Improved shift comfort.
•
More favourable step-up through the five gears.
•
Increased service life and reliability.
•
Lower maintenance costs.
TRANSMISSION IDENTIFICATION
The transmission can be generically identified visually by the presence of a round 13-way connector located near
the front corner of the transmission oil pan, on the right side. Specific transmission information can be found
stamped into a pad on the left side of the transmission, above the oil pan rail.
TRANSMISSION GEAR RATIOS
The gear ratios for the NAG1 automatic transmission are as follows:
1st Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.59:1
2nd Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.19:1
3rd Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.41:1
4th Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.00:1
5th Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.83:1
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.16:1
TRANSMISSION HOUSING
The converter housing and transmission are made from a light alloy. These are bolted together and centered via the
outer multi-disc carrier of multi-disc holding clutch, B1. A coated intermediate plate provides the sealing. The oil
pump and the outer multi-disc carrier of the multi-disc holding clutch, B1, are bolted to the converter housing. The
stator shaft is pressed into it and prevented from rotating by splines. The electrohydraulic unit is bolted to the trans-
mission housing from underneath. A sheet metal steel oil pan forms the closure.
MECHANICAL SECTION
The mechanical section consists of a input shaft, output shaft, a sun gear shaft, and three planetary gear sets which
are coupled to each other. The planetary gear sets each have four planetary pinion gears. The oil pressure for the
torque converter lock-up clutch and clutch K2 is supplied through bores in the input shaft. The oil pressure to clutch
K3 is transmitted through the output shaft. The lubricating oil is distributed through additional bores in both shafts.
All the bearing points of the gear sets, as well as the freewheeling clutches and actuators, are supplied with lubri-
cating oil. The parking lock gear is connected to the output shaft via splines.
Freewheeling clutches F1 and F2 are used to optimize the shifts. The front freewheel, F1, is supported on the
extension of the stator shaft on the transmission side and, in the locking direction, connects the sun gear of the front
planetary gear set to the transmission housing. In the locking direction, the rear freewheeling clutch, F2, connects
the sun gear of the center planetary gear set to the sun gear of the rear planetary gear set.
ELECTROHYDRAULIC CONTROL UNIT
The electrohydraulic control unit comprises the shift plate made from light alloy for the hydraulic control and an
electrical control unit. The electrical control unit comprises of a supporting body made of plastic, into which the
electrical components are assembled. The supporting body is mounted on the shift plate and screwed to it.
Strip conductors inserted into the supporting body make the connection between the electrical components and a
plug connector. The connection to the wiring harness on the vehicle and the transmission control module (TCM) is
produced via this 13-pin plug connector with a bayonet lock.
SHIFT GROUPS
The hydraulic control components (including actuators) which are responsible for the pressure distribution before,
during, and after a gear change are described as a shift group. Each shift group contains a command valve, a
holding pressure shift valve, a shift pressure shift valve, overlap regulating valve, and a solenoid.
The hydraulic system contains three shift groups: 1-2/4-5, 2-3, and 3-4. Each shift group can also be described as
being in one of two possible states. The active shift group is described as being in the shift phase when it is actively
LX
AUTOMATIC TRANSMISSION NAG1 - SERVICE INFORMATION
21 - 265
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст