Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 484
U0019–CAN B BUS
For a complete wiring diagram Refer to Section 8W.
8J - 40
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
LX
•
When Monitored:
With the Instrument Cluster awake.
•
Set Condition:
Whenever the Can B Bus (+) or B Bus (–) circuit is open, shorted to voltage or shorted to ground, this code
will set.
Possible Causes
CAN B BUS DTCs IN FRONT CONTROL MODULE
(D54) CAN B BUS (–) CIRCUIT OPEN
(D55) CAN B BUS (+) CIRCUIT OPEN
INSTRUMENT CLUSTER
Diagnostic Test
1.
CHECK FOR AN ACTIVE DTC
Turn the ignition on.
With the scan tool, record and erase DTCs.
Cycle the ignition from on to off 3 times.
Turn the ignition on.
With the scan tool, read DTCs.
Is the DTC active?
Yes
>> Go To 2
No
>> The condition that caused this code to set is not present at this time. Check for an intermittent condition
by inspecting the related wiring harness for chafed, pierced, pinched, and partially broken wires. Also
inspect the related connectors for broken, bent, pushed out, spread, corroded, or contaminated termi-
nals.
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
2.
CHECK FRONT CONTROL MODULE DTCs
With the scan tool, read Front Control Module DTCs.
Does the scan tool display the U0019–CAN B BUS DTC?
Yes
>> Refer to the symptom list for problems related to Communication in the ELECTRICAL.– ELECTRONIC
CONTROL MODULES – ELECTRICAL DIAGNOSES section.
No
>> Go to 3
Perform BODY VERIFICATION TEST - VER 1. (Refer to BODY VERIFICATION TEST - VER 1).
LX
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
8J - 41
3.
CAN B BUS (+) CIRCUIT OPEN
Turn the ignition off.
Disconnect the Instrument Cluster C1 harness connector.
Disconnect the Front Control Module C1 harness connector.
Measure the resistance of the (D55) Can B Bus (+) circuit between the
Front Control Module C1 harness connector and the Instrument Cluster
C1 harness connector.
Is the resistance below 2.0 ohms?
Yes
>> Go To 4
No
>> Repair the Can B Bus (+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).
4.
CAN B BUS (–) CIRCUIT OPEN
Measure the resistance of the (D54) Can B Bus (–) circuit between the
Front Control Module C1 harness connector and the Instrument Cluster
C1 harness connector.
Is the resistance below 2.0 ohms?
Yes
>> Replace the Instrument Cluster in accordance with the ser-
vice information.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).
No
>> Repair the Can B Bus (–) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1. (Refer to
BODY VERIFICATION TEST - VER 1).
8J - 42
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
LX
U0141–LOST COMMUNICATION WITH FRONT CONTROL MODULE
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0151-LOST COMMUNICATION WITH OCCUPANT RESTRAINT CONTROLLER
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0159-LOST COMMUNICATION WITH PARKING ASSIST CONTROL MODULE
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0164-LOST COMMUNICATION WITH HVAC CONTROL MODULE
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0167-LOST COMMUNICATION WITH INTRUSION TRANSCEIVER CONTROL
MODULE
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0168-LOST COMMUNICATION WITH VEHICLE SECURITY CONTROL MODULE
(SKREEM/WCM)
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0184-LOST COMMUNICATION WITH RADIO
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0195-LOST COMMUNICATION WITH SDARS
For a complete wiring diagram Refer to Section 8W.
(Refer to 8 - ELECTRICAL/ELECTRONIC CONTROL MODULES - DIAGNOSIS AND TESTING) for the diagnostic
test procedure.
U0197-LOST COMMUNICATION WITH HANDS FREE PHONE MODULE
For a complete wiring diagram Refer to Section 8W.
LX
INSTRUMENT CLUSTER - ELECTRICAL DIAGNOSTICS
8J - 43
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст