Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 181
7. Connect parking brake release cable (4) at handle (5) in steering column opening cover (1).
8. Connect wiring connector (3) at decklid release switch.
9. Position steering column opening cover (1) and install fasteners (6) securing it in place.
10. Raise and support vehicle.
NOTE: Due to short travel and low spring tension,
it is not necessary to lock-out parking brake lever
to service parking brake components.
11. Connect front parking brake cable (5) at connector
(3) to right rear parking brake cable (4).
12. Lower vehicle until rear wheels are just above
floor level.
13. Apply parking brake lever. Release lever to test
release cable and handle. Reapply lever. While
doing this, check to make sure the red indicator
lamp in the cluster turns on and off properly.
14. Check to make sure rear wheels will not rotate
with lever applied.
15. Release parking brake lever, then check to make
sure rear wheels rotate without excessive drag.
16. Apply parking brake lever.
17. Lower vehicle.
5 - 166
BRAKES - BASE
LX
LEVER - RHD
1. Install parking brake lever (7) over mounting studs
(2, 3).
2. Install two nuts (8) mounting left side of parking
brake lever to body. Tighten nuts to 26 N·m (19 ft.
lbs.).
3. Tighten nut (5) left on stud (3) to 26 N·m (19 ft. lbs.).
4. Connect wiring connector at parking brake switch.
5. Guide front parking brake cable strand (3) up
through lever bracket and press cable housing
retainer (4) into bracket allowing retainer fingers to
lock cable in place.
6. Connect parking brake cable strand (3) at lever
connector (2).
7. If installing new lever, remove pin locking out auto-
matic tensioning spring.
8. Reposition carpet back to original position at center console.
9. Install foot rest. (Refer to 23 - BODY/INTERIOR/FRONT FLOOR FOOT REST - INSTALLATION)
10. Install steering column opening cover. (Refer to 23 - BODY/INSTRUMENT PANEL/STEERING COLUMN
OPENING COVER - INSTALLATION)
11. Install driver side silencer under instrument panel. (Refer to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT
PANEL SILENCER - INSTALLATION)
12. Raise and support vehicle.
LX
BRAKES - BASE
5 - 167
NOTE: Due to short travel and low spring tension,
it is not necessary to lock-out parking brake lever
to service parking brake components.
13. Connect front parking brake cable (5) at connec-
tor (2) to left rear parking brake cable (1).
14. Lower vehicle until rear wheels are just above
floor level.
15. Apply parking brake lever. Release lever to test
release cable and handle. Reapply lever. While
doing this, check to make sure the red indicator
lamp in the cluster turns on and off properly.
16. Check to make sure rear wheels will not rotate
with lever applied.
17. Release parking brake lever, then check to make
sure rear wheels rotate without excessive drag.
18. Apply parking brake lever.
19. Lower vehicle.
5 - 168
BRAKES - BASE
LX
SHOE AND LINING - PARKING BRAKE
REMOVAL
NOTE: The following procedure may be used to remove shoes on either side of the vehicle.
1. Raise and support vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE)
2. Access and remove rear hub and bearing. (Refer to 2 - SUSPENSION/REAR/HUB / BEARING - REMOVAL)
3. Completely back off parking brake shoe adjustment
(8).
4. Remove parking brake shoe adjuster spring (3).
5. Remove shoe adjuster (8).
6. Remove upper brake shoe hold-down clip and pin
(7).
7. Remove upper shoe (6) from return spring (4) and
shoe actuator lever (1).
8. Remove return spring (4) from lower shoe (6).
9. Remove shoe actuator lever (1) from end of cable
(2).
10. Remove lower brake shoe hold-down clip and pin
(7).
11. Remove lower shoe (6).
12. Inspect springs, adjuster, lever and aluminum
shoe anchor pin for wear or damage. Replace as
necessary.
LX
BRAKES - BASE
5 - 169
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст