Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 267
5.7L/6.1L ENGINE
1. Install water pump and mounting bolts (2). Tighten
mounting bolts to 28 N·m (20 ft. lbs.).
2. Make sure double ended bolt (3) is in the proper
location. Tighten double ended bolt to 28 N·m (20
ft. lbs.).
3. Install thermostat (Refer to 7 - COOLING/ENGINE/
ENGINE COOLANT THERMOSTAT - INSTALLA-
TION).
4. Install accessory drive belt (Refer to 7 - COOLING/
ACCESSORY DRIVE/DRIVE BELTS - INSTALLA-
TION).
5. Install the radiator fan assembly (Refer to 7 -
COOLING/ENGINE/RADIATOR FAN - INSTALLA-
TION).
6. Connect negative battery cable.
7. Fill cooling system (Refer to 7 - COOLING - STAN-
DARD PROCEDURE).
8. Pressure test cooling system (Refer to 7 - COOL-
ING - DIAGNOSIS AND TESTING).
3.0L DIESEL
1. Clean all sealing surfaces.
2. Position and install water pump. Tighten M6 bolts
to 14 N·m (124 lbs. in.) and M8 bolts to 20 N·m
(177 lbs. in.).
3. Install idler pulley. Tighten bolt to 35 N·m (26 lbs.
ft.).
4. Install coolant hoses.
5. Install accessory drive belt (Refer to 7 - COOLING/
ACCESSORY DRIVE/DRIVE BELTS - INSTALLA-
TION).
6. Close coolant drain.
7. Install engine cover (Refer to 9 - ENGINE -
INSTALLATION).
8. Connect negative battery cable.
9. Fill coolant system to proper level with the appro-
priate coolant mixture (Refer to 7 - COOLING/EN-
GINE/COOLANT - STANDARD PROCEDURE).
WARNING: Use extreme caution when engine is operating. Do not put your hands near pulleys, belts or fan.
Do not wear loose clothes.
10. Start engine and inspect for leaks.
7 - 72
ENGINE
LX
FAN-RADIATOR
REMOVAL
1. Disconnect negative battery cable.
2. Partially drain cooling system (Refer to 7 - COOL-
ING - STANDARD PROCEDURE).
3. Remove upper radiator hose (3).
4. Disconnect cooling fan electrical connector (2).
5. Remove cooling fan mounting bolts.
6. Remove radiator cooling fan assembly (1) from
vehicle.
INSTALLATION
1. Position radiator cooling fan assembly (1) in vehi-
cle.
2. Install cooling fan mounting bolts. Tighten to 6 N·m
(50 in. lbs.)
3. Connect cooling fan electrical connector (2).
4. Install upper radiator hose (3).
5. Fill cooling system (Refer to 7 - COOLING - STAN-
DARD PROCEDURE).
6. Operate engine until it reaches normal operating
temperature. Check cooling system and automatic
transmission for correct fluid levels.
LX
ENGINE
7 - 73
TRANSMISSION
TABLE OF CONTENTS
page
page
TRANSMISSION
TRANSMISSION COOLER LINE QUICK
TRANSMISSION COOLER
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
TRANSMISSION COOLER LINES
7 - 74
TRANSMISSION
LX
TRANSMISSION
STANDARD PROCEDURE
TRANSMISSION COOLER LINE QUICK CONNECT FITTING DISASSEMBLY/
ASSEMBLY
DISCONNECT
1. Remove dust cap by pulling it straight back off of
quick connect fitting.
2. Place disconnect tool 8875A onto transmission
cooler line with the fingers of the tool facing the
quick connect fitting.
3. Slide disconnect tool down the transmission line
and engage the fingers of the tool into the retaining
clip. When properly engaged in the clip, the tool
will fit flush against the quick connect fitting.
4. Rotate the disconnect tool 60° to expand the
retaining clip.
5. While holding the disconnect tool against the quick
connect fitting, pull back on the transmission cooler
line to remove.
LX
TRANSMISSION
7 - 75
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст