Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 375
3.
(Z910) GROUND CIRCUIT OPEN
Using a 12-volt test light connected to 12-volts, check the (Z910)
ground circuit.
Does the test light illuminate brightly?
Yes
>> Go To 4
No
>> Repair the (Z910) ground circuit for an open.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
4.
(D55) AND (D54) CAN B BUS CIRCUITS OPEN
NOTE: One open circuit will not cause this condition.
Measure the voltage between the (D54) CAN B Bus (-) circuit and
ground.
Measure the voltage between the (D55) CAN B Bus (+) circuit and
ground.
Is there any voltage present on either circuit?
Yes
>> Replace the Intrusion Transceiver Module in accordance
with the service information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
No
>> Repair the (D55) and (D54) CAN B Bus circuits for an open.
Inspect the connector for damage.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
8E - 190
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
LX
*NO RESPONSE FROM LRSM (LIGHT/RAIN SENSOR MODULE)
For a complete wiring diagram Refer to Section 8W.
LX
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
8E - 191
Possible Causes
(F880) FUSED ACCESSORY DELAY RELAY OUTPUT CIRCUIT OPEN OR SHORTED
(Z909) GROUND CIRCUIT OPEN
(D55) AND (D54) CAN B BUS CIRCUITS OPEN
LIGHT/RAIN SENSOR MODULE
Diagnostic Test
1.
TEST FOR INTERMITTENT CONDITION
Turn the ignition on.
NOTE: Ensure the IOD fuse is installed and battery voltage is between 10.0 and 16.0 volts.
With the scan tool, select ECU View.
NOTE: A red X will be next to the module that is not communicating, indicating that the module is not active
on the Bus network. A green check indicates that the module is active on the Bus network.
Does the scan tool display a red X next to the module?
Yes
>> Go To 2
No
>> The no response condition is not present at this time. Using the wiring diagram/schematic as a guide,
inspect the wiring for chafed, pierced, pinched, and partially broken wires and the wiring harness con-
nectors for broken, bent, pushed out, and corroded terminals.
2.
(F880) FUSED ACCESSORY DELAY RELAY OUTPUT CIRCUIT OPEN OR SHORTED
NOTE: Check the FCM for any ignition related DTCs before pro-
ceeding. If set (Refer to 8 - ELECTRICAL/IGNITION CONTROL -
DIAGNOSIS AND TESTING).
Turn the ignition off.
Disconnect the Light/Rain Sensor harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the (F880) Fused
Accessory Delay Relay Output circuit.
Does the test light illuminate brightly?
Yes
>> Go To 3
No
>> Repair the (F880) Fused Accessory Delay Relay Output cir-
cuit for an open or short.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
8E - 192
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
LX
3.
(Z909) GROUND CIRCUIT OPEN
Turn the ignition off.
Using a 12-volt test light connected to 12-volts, check the (Z909)
ground circuit.
Does the test light illuminate brightly?
Yes
>> Go To 4
No
>> Repair the (Z909) ground circuit for an open.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
4.
(D55) AND (D54) CAN B BUS CIRCUITS OPEN
NOTE: One open circuit will not cause this condition.
Measure the voltage between the (D54) CAN B Bus (-) circuit and
ground.
Measure the voltage between the (D55) CAN B Bus (+) circuit and
ground.
Is there any voltage present on either circuit?
Yes
>> Replace the Light/Rain Sensor in accordance with the ser-
vice information.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
No
>> Repair the (D55) and (D54) CAN B Bus circuits for an
open. Inspect the connector for damage.
Perform BODY VERIFICATION TEST – VER 1. (Refer to
BODY VERIFICATION TEST – VER 1).
LX
ELECTRONIC CONTROL MODULES - ELECTRICAL DIAGNOSTICS
8E - 193
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст