Chrysler New Yorker. Manual — part 533

TEST 11A

REPAIRING - HEADLAMP WASHERS NOT WORKING PROPERLY

Perform TEST 1A Before Proceeding

FIG. 1

FIG. 2

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

730

TEST 11A

REPAIRING - HEADLAMP WASHERS NOT WORKING PROPERLY

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION
OF ALL COMPONENTS.

START TEST 11A.

SEE GENERAL INFO 4.0

PERFORM

TURN THE IGNITION

TURN THE LOW BEAM

DO THE HEADLAMPS

NO

"EXTERIOR

ON.

HEADLAMPS ON.

OPERATE PROPERLY?

LIGHTING" TEST

1A.

YES

PUSH AND THEN

TURN THE WIPERS TO

RELEASE THE WASH

DID THE WIPERS AND

NO

PERFORM TEST

THE LOW SPEED

BUTTON ON THE

WASHERS OPERATE

1A.

SETTING. WIPER SWITCH.

PROPERLY?

YES

SYSTEM IS

DID THE HEADLAMP YES

OPERATEING

WASHERS TURN ON?

PROPERLY WITH NO

PROBLEM FOUND.

NO

SUBSITUTE THE

WITH THE HEADLAMPS

HEADLAMP WASHER

ON, PUSH THE WASH

DID THE HEADLAMP

YES

REPLACE THE

RELAY WITH A KNOWN

BUTTON ON THE

WASHERS TURN ON?

ORIGINAL HEADLAMP

GOOD RELAY.

WIPER SWITCH.

WASHER RELAY.*

FIG. 1

NO

DISCONNECT THE

WITH AN OHMMETER,

HEADLAMP WASHER

MEASURE BETWEEN

IS THE RESISTANCE

NO

REPAIR THE OPEN

MOTOR HARNESS

GROUND AND THE

BELOW 5.0 OHMS?

GROUND CIRCUIT.*

CONNECTOR.** GROUND

CIRCUIT.

FIG. 2

YES

CONTINUE TEST
11A ON THE NEXT

PAGE.

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

731

TEST 11A

CONTINUED - REPAIRING HEADLAMP WASHERS NOT WORKING PROPERLY

FIG. 1

FIG. 2

FIG. 3

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

732

TEST 11A

CONTINUED - REPAIRING HEADLAMP WASHERS NOT WORKING PROPERLY

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST 11A

CONNECT A TEST LIGHT

CONTINUED FROM BETWEEN THE HEADLAMP

THE PREVIOUS WASHER

MOTOR

PAGE.

CONNECTOR CAVITIES

1 & 2. FIG. 1

DOES THE TEST

WITH THE DRB ENTER

ACTUATE THE

LIGHT FLASH ON AND

YES

REPLACE THE

"BODY COMPUTER"

HEADLAMP WASHER

OFF AS THE RELAY

HEADLAMP WASHER

THEN "ACTUATORS".

RELAY.

IS ACTUATED?

MOTOR.*

NO

REMOVE THE HEADLAMP

STOP THE

WASHER RELAY.

ACTUATION.

FIG. 2

WITH A VOLTMETER,
MEASURE BOTH FUSED

IS THE VOLTAGE

NO

REPAIR THE OPEN

B(+) CIRCUITS.

ABOVE 10.0 VOLTS

FUSED B(+)

ON BOTH CIRCUITS?

CIRCUITS.*

FIG. 2

YES

CONNECT A JUMPER

WITH AN OHMMETER,

REPAIR THE OPEN

WIRE BETWEEN GROUND

MEASURE BETWEEN GND

IS THE RESISTANCE

NO

HEADLAMP WASHER

AND CAVITY 4 OF THE

AND THE HEADLAMP

BELOW 5.0 OHMS?

MOTOR CONTROL

HEADLAMP WASHER

WASHER MOTOR CONTROL

CIRCUIT.*

RELAY CONN. FIG. 2

CKT. FIG. 1

YES

CONNECT A JUMPER

WIRE BETWEEN GROUND

DISCONNECT THE BCM

AND CAVITY 1 OF THE

"C3" HARNESS

HEADLAMP WASHER

CONNECTOR.**

RELAY CONN. FIG. 2

WITH AN OHMMETER,

REPAIR THE OPEN

MEASURE BETWEEN GND

IS

THE RESISTANCE NO HEADLAMP

WASHER

AND THE HEADLAMP BELOW 5.0 OHMS?

RELAY CONTROL

WASHER RELAY CONTROL

CIRCUIT.*

CKT. FIG. 3

YES

REPLACE THE BODY
CONTROL MODULE.*

W

I

N
D

S

H

I

E

L

D

W

I

P
E

R

S
Y
S

T

E

M

733