Chrysler New Yorker. Manual — part 88
LAMP BULB SERVICE
INDEX
page
page
REMOVAL AND INSTALLATION
CHMSL AND APPLIQUE LAMP BULB(S) –
INTREPID . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
CHMSL BULB(S) – CONCORDE/LHS . . . . . . . . . 10
CHMSL LAMP BULB – 300M . . . . . . . . . . . . . . . 10
DECK LID LAMP BULB . . . . . . . . . . . . . . . . . . . . 15
FOG LAMP BULB – INTREPID/300M . . . . . . . . . 11
FOG LAMP BULB – LHS . . . . . . . . . . . . . . . . . . . 11
FRONT PARKING AND TURN SIGNAL
LAMP BULB - LHS . . . . . . . . . . . . . . . . . . . . . 12
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB – CONCORDE . . . . . . . . 12
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB – INTREPID . . . . . . . . . . 12
FRONT SIDE MARKER LAMP BULB – LHS . . . . 12
HEADLAMP BULB(S) –
CONCORDE/LHS/300M . . . . . . . . . . . . . . . . . . 13
HEADLAMP BULBS – INTREPID . . . . . . . . . . . . 13
LICENSE PLATE LAMP BULB –
REAR BUMPER FASCIA . . . . . . . . . . . . . . . . . 14
TAIL, STOP, BACK UP, AND TURN SIGNAL
LAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . . 14
REMOVAL AND INSTALLATION
CHMSL BULB(S) – CONCORDE/LHS
REMOVAL
(1) Release deck lid latch and open deck lid.
(2) From under rear shelf panel, disconnect the
lamp socket from the CHMSL housing (Fig. 1).
(3) Remove bulb from the socket.
INSTALLATION
(1) Install the bulb into the socket.
(2) Install socket into CHMSL housing.
(3) Verify CHMSL operation.
CHMSL AND APPLIQUE LAMP BULB(S) –
INTREPID
REMOVAL
(1) Release deck lid latch and open trunk lid.
(2) Remove deck lid cover.
(3) Disconnect lamp socket from housing (Fig. 2).
(4) Remove bulb from socket.
INSTALLATION
(1) Install bulb into socket.
(2) Install socket into housing.
(3) Verify CHMSL operation.
(4) Install deck lid cover.
CHMSL LAMP BULB – 300M
REMOVAL
(1) Release deck lid latch and open deck lid.
(2) Remove deck lid cover.
(3) Disconnect lamp socket(s) from housing (Fig. 3).
(4) Remove bulb(s) from socket(s).
Fig. 1 CHMSL – Rear Shelf
Fig. 2 CHMSL – Intrepid
8L - 10
LAMPS
300M
INSTALLATION
(1) Install bulb(s) in socket(s).
(2) Install socket(s) into housing.
(3) Verify CHMSL operation.
(4) Install deck lid cover.
FOG LAMP BULB – INTREPID/300M
REMOVAL
(1) Remove fog lamp housing screw in front fascia
and pull lamp housing from the fascia.
(2) Remove rear cover from fog lamp housing.
(3) Disengage wire clip holding bulb in fog lamp.
(4) Hinge wire clip out of bulb removal path.
(5) Pull bulb from lamp housing (Fig. 4) or (Fig. 5).
(6) Disengage wire connector from body wire harness.
INSTALLATION
CAUTION:
Do not touch the glass of halogen
bulbs with fingers or other possibly oily surface,
reduced bulb life will result.
(1) Connect wire connector to body wire harness.
(2) Cover exposed terminal with teflon coated
sleeve.
(3) Insert bulb into lamp housing.
(4) Hinge wire clip over bulb base.
(5) Engage wire clip to hold bulb in fog lamp.
(6) Install rear cover to fog lamp housing.
(7) Verify fog lamp operation and alignment.
(8) Install fog lamp housing screw to the front fascia.
FOG LAMP BULB – LHS
REMOVAL
(1) Remove fog lamp housing screw in front fascia
and pull lamp housing from the front fascia.
(2) Disconnect wire connector from fog lamp socket
(Fig. 6).
(3) Rotate socket and pull bulb/socket from lamp
housing.
INSTALLATION
CAUTION:
Do not touch the glass of halogen
bulbs with fingers or other possibly oily surface,
reduced bulb life will result.
(1) Install socket into fog lamp housing and rotate
to the lock position.
(2) Connect wire connector to the socket.
(3) Verify fog lamp operation and alignment.
(4) Install fog lamp housing into fascia.
(5) Install fog lamp screw to the front fascia.
Fig. 3 CHMSL – 300M
Fig. 4 Fog Lamp Bulb – Intrepid
Fig. 5 Fog Lamp Bulb – 300M
300M
LAMPS
8L - 11
REMOVAL AND INSTALLATION (Continued)
FRONT PARKING AND TURN SIGNAL LAMP BULB
- LHS
REMOVAL
(1) Remove headlamp housing from vehicle.
(2) Disconnect wire connector from back of lamp
socket(s).
(3) Rotate socket and pull lamp socket from head-
lamp housing (Fig. 7).
(4) Remove bulb from lamp socket.
INSTALLATION
(1) Push bulb into lamp socket.
(2) Place lamp socket into headlamp housing and
rotate to the lock position.
(3) Connect wire connector to lamp socket(s).
(4) Verify headlamp operation.
(5) Install headlamp housing.
(6) Verify headlamp operation and alignment.
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB – CONCORDE
REMOVAL
(1) Reach under the fascia and remove the socket
from the lamp housing (Fig. 8).
(2) Rotate and pull socket from lamp housing.
(3) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Install socket into lamp housing.
(3) Verify park and turn signal lamp operation.
FRONT PARKING, SIDE MARKER, AND TURN
SIGNAL LAMP BULB – INTREPID
REMOVAL
(1) Release hood latch and open hood.
(2) Remove
jackscrews
attaching
headlamp
to
crossmember.
(3) Remove lamp housing to access the lamp
socket.
(4) Remove lamp socket from lamp housing (Fig. 9).
(5) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Install lamp socket in lamp housing.
(3) Verify lamp operation.
(4) Place headlamp in position on vehicle.
(5) Install jackscrews to attach headlamp housing
to crossmember.
FRONT SIDE MARKER LAMP BULB – LHS
REMOVAL
(1) Reach under the fascia and remove the socket
from the side marker lamp housing (Fig. 10).
Fig. 8 Parking, Side Marker, and Turn Signal Lamp
Bulb – Concorde
Fig. 6 Fog Lamp Bulb – LHS
Fig. 7 Front Parking and Turn Signal Lamp Bulb –
LHS
8L - 12
LAMPS
300M
REMOVAL AND INSTALLATION (Continued)
(2) Pull bulb from socket.
INSTALLATION
(1) Push bulb into socket.
(2) Install socket into front side marker lamp
housing.
(3) Verify park and front side marker lamp opera-
tion.
HEADLAMP BULB(S) – CONCORDE/LHS/300M
REMOVAL
(1) Remove headlamp housing. Refer to Headlamp
Housing - Concorde/LHS/300M for proper procedures.
(2) Rotate retaining ring (High beam or Low beam)
and pull lamp socket from headlamp housing (Fig.
11).
(3) Remove bulb from lamp socket.
INSTALLATION
CAUTION:
Do not touch the glass of halogen
bulbs with fingers or other possibly oily surface,
reduced bulb life will result.
(1) Push bulb into lamp socket.
(2) Place lamp socket into headlamp housing and
rotate retaining ring to the lock position.
(3) Install headlamp housing.
HEADLAMP BULBS – INTREPID
REMOVAL
(1) Release hood latch and open hood.
(2) Remove jackscrews attaching headlamp hous-
ing to crossmember and remove the lamp housing to
access the lamp(s).
(3) Disconnect wire connector from back of lamp
socket (Fig. 12).
(4) Rotate retaining ring (High beam or Low beam)
and pull lamp socket from headlamp housing.
(5) Remove bulb from lamp socket.
INSTALLATION
CAUTION:
Do not touch the glass of halogen
bulbs with fingers or other possibly oily surface,
reduced bulb life will result.
Fig. 9 Parking, Side Marker, and Turn Signal Bulb -
Intrepid
Fig. 10 Front Side Marker Lamp Bulb – LHS
Fig. 11 Headlamp Bulb Removal
Fig. 12 Headlamp Bulb – Intrepid
300M
LAMPS
8L - 13
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст