Chrysler New Yorker. Manual — part 422

TEST 9A

CONTINUED - REPAIRING FOG LAMPS THAT WILL NOT TURN ON

FIG. 1

FIG. 2

FIG. 3

E
X

T

E

R

I

O

R

L

I

G

H

T

I

N

G

S
Y
S

T

E

M

286

TEST 9A

CONTINUED - REPAIRING FOG LAMPS THAT WILL NOT TURN ON

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST 9A

CONTINUED FROM STOP

THE FOG LAMP

THE PREVIOUS RELAY ACTUATION.

PAGE.

TURN THE HEADLAMPS

REPAIR THE OPEN

ON AND ATTEMPT TO

DO THE HIGH BEAM

NO

FUSED B(+) CIRCUIT

OPERATE THE HIGH HEADLAMPS OPERATE

FROM

THE PDC FUSE

BEAM HEADLAMPS.

PROPERLY?

"C". IF OK,

REPLACE THE J/B.*

YES

INSPECT FUSE #16

IN JUNCTION BLOCK.

YES

CONTINUE TEST

IS THE FUSE OPEN?

9A ON THE NEXT

PAGE.

FIG. 1

NO

REMOVE THE FOG

USING A VOLTMETER,

LAMP RELAY.

MEASURE THE FUSED

IS THE VOLTAGE

NO

REPLACE THE

B(+) CIRCUIT

ABOVE 10.0 VOLTS?

JUNCTION BLOCK.*

(CAVITY 65).

FIG. 2

FIG. 2

YES

CONNECT A TEST

LIGHT BETWEEN

WITH THE DRB,

DID THE TEST LIGHT

YES

REPLACE THE FOG

RELAY

ACTUATE THE FOG

FLASH DURING LAMP

RELAY.*

CON

LAMP RELAY.

ACTUATION?

NO

REMOVE THE BODY

CONTROL MODULE

FROM THE JUNCTION

BLOCK.

USING AN OHMMETER,

AND THE J/B 20-WAY

MEASURE BETWEEN

INTERNAL CONNECTOR

IS THE RESISTANCE

NO

REPLACE THE

THE FOG LAMP RELAY

TERMINAL 17.

BELOW 5.0 OHMS?

JUNCTION BLOCK.*

CONNECTOR

CAVITY 64...

FIGS. 2 & 3

YES

REPLACE THE BODY
CONTROL MOULE.*

THE

FOG LAMP

N CAVITIES

64 & 65. FIG. 2

E
X

T

E

R

I

O

R

L

I

G

H

T

I

N

G

S
Y
S

T

E

M

287

TEST 9A

CONTINUED - REPAIRING FOG LAMPS THAT WILL NOT TURN ON

FIG. 1

E
X

T

E

R

I

O

R

L

I

G

H

T

I

N

G

S
Y
S

T

E

M

288

TEST 9A

CONTINUED - REPAIRING FOG LAMPS THAT WILL NOT TURN ON

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST 9A

REMOVE THE FOG

CONTINUED FROM LAMP

RELAY.

THE PREVIOUS

PAGE.

FIG. 1

WITH AN OHMMETER,

MEASURE BETWEEN

IS THE RESISTANCE

YES

REPLACE THE

GROUND AND THE FOG

BELOW 5.0 OHMS?

JUNCTION BLOCK.*

LAMP RELAY CONN

CAVITY 66. FIG. 1

NO

WITH AN OHMMETER,

REPAIR THE FOG LAMP

MEASURE BETWEEN

IS THE RESISTANCE

YES

RELAY OUTPUT CIRCUIT

GROUND AND THE FOG

BELOW 5.0 OHMS?

FOR A SHORT TO

LAMP RELAY CONN

GROUND. IF OK,

CAVITY 67. FIG. 1

REPLACE THE J/B.*

NO

REPLACE THE FUSE.

E
X

T

E

R

I

O

R

L

I

G

H

T

I

N

G

S
Y
S

T

E

M

289