Chrysler New Yorker. Manual — part 252
FRAMES AND BUMPERS
CONTENTS
page
page
BUMPERS AND FASCIAS . . . . . . . . . . . . . . . . . . . 1
FRAME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BUMPERS AND FASCIAS
INDEX
page
page
REMOVAL AND INSTALLATION
CONCORDE/LHS/300M . . . . . . . . . . . . . . . . . . . 1
FRONT BUMPER FASCIA – INTREPID . . . . . . . . . 2
FRONT BUMPER REINFORCEMENT . . . . . . . . . . 3
CONCORDE/LHS/300M . . . . . . . . . . . . . . . . . . . 3
REAR BUMPER FASCIA – INTREPID . . . . . . . . . . 3
REAR BUMPER REINFORCEMENT . . . . . . . . . . . 4
REMOVAL AND INSTALLATION
FRONT BUMPER FASCIA – CONCORDE/LHS/300M
REMOVE
(1) Release hood latch and open hood.
(2) Remove large rubber grommet (70 mm x 168
mm) from splash shield to gain access to fascia fas-
teners (Fig. 1).
(3) Remove fasteners attaching fascia to the front
fender and splash shield, using access hole in splash
shield (Fig. 2).
(4) Remove the fasteners attaching the fascia to
the lower crossmember (Fig. 3).
(5) Remove the fasteners attaching the fascia to
the upper radiator closure panel (Fig. 3).
(6) Disconnect wire connectors (fog lamps, parking/
turn signal, side marker), if equipped (Fig. 4).
(7) Remove fascia from vehicle.
INSTALLATION
(1) Connect wire connectors.
(2) Place fascia in position on vehicle, by fitting
foam to bumper beam. Use care not to scratch fender.
Tape may be put on fender for protection.
(3) Install the top center fasteners, to upper radi-
ator closure panel.
(4) Install fasteners attaching fascia to the front
fender and splash shield, using access hole in splash
shield
(5) Align fascia to bumper reinforcement.
(6) Align the two fascia studs to the fender vertical
attachments, at the same time align the fascia groove
on the horizontal flange with the fender fasteners.
Push fascia rearward to engage the fasteners.
(7) Install nut on fascia stud through the splash
shield access hole, on each side.
Fig. 1 Access Rubber Grommet
300M
FRAMES AND BUMPERS
13 - 1
FRONT BUMPER FASCIA – INTREPID
REMOVAL
(1) Release hood latch and open hood.
(2) Remove push in fasteners attaching bottom of
fascia (air dam) to radiator closure panel (Fig. 5).
(3) Remove fasteners attaching fascia to front
fenders and splash shields (Fig. 6).
(4) Remove push in fasteners attaching the fascia
to upper radiator closure panel.
(5) Pull the sides of the fascia outwards to disen-
gage fascia from drive pins then pull fascia forward.
(6) Disconnect
fog
lamp
wire
connectors,
if
equipped.
(7) Remove fascia from vehicle.
INSTALLATION
(1) Connect fog lamp wire connectors, if equipped.
(2) Place fascia in position on vehicle, by fitting
foam to bumper beam.
(3) Snap sides of fascia over drive pin fasteners on
fenders.
(4) Install fasteners to upper radiator closure.
(5) Install fasteners attaching fascia to front fend-
ers and splash shields.
(6) Install fasteners attaching bottom of fascia to
radiator closure panel.
Fig. 2 Fastener Locations
Fig. 3 Remove Push In Fasteners
Fig. 4 Front Bumper Fascia
Fig. 5 Air Dam
Fig. 6 Front Bumper Fascia
13 - 2
FRAMES AND BUMPERS
300M
REMOVAL AND INSTALLATION (Continued)
FRONT BUMPER REINFORCEMENT
REMOVAL
(1) Remove front fascia.
(2) Remove end plugs in ends of bumper after
removing screws in front of bumper.
(3) Remove attaching bolts from bumper reinforce-
ment to adapter plate through ends of the bumper.
(Fig. 7).
(4) If beam is damaged, the adapter plate to rail
welds will have to be cut off.
INSTALLATION
(1) Place reinforcement in position on front of vehi-
cle.
(2) Install attaching bolts to inside of bumper rein-
forcement to adapter plates.
(3) Install end plugs in ends of bumper, using
screws in front of the bumper.
(4) Install front fascia.
REAR BUMPER FASCIA – CONCORDE/LHS/300M
REMOVAL
(1) Release deck lid latch and open deck lid.
(2) Partially remove trunk carpet to gain access to
fascia attaching nuts and remove nuts.
(3) Remove both tail lamp housings to gain access
to fascia attaching nuts (300M).
(4) Remove nuts from the attaching studs.
(5) Remove fasteners attaching fascia to rear quar-
ter and splash shield.
(6) Remove upper push pins attaching the fascia to
the body.
(7) Pull fascia with 30 pound force to disengage
plastic clip and grommet that attaches the fascia to
the quarter panel vertical flange one side at a time
(Fig. 8).
(8) Disengage main wire connector from the body
harness. The connector is on the left side of vehicle.
(9) Remove fascia from vehicle.
INSTALLATION
(1) Connect main wire connector to the body har-
ness connector.
(2) Place rear fascia in position on bumper rein-
forcement.
(3) Align the two fascia studs to the quarter panel
vertical attachment, at the same time align the fas-
cia key hole slot on the horizontal flange with the
drive pin. Push fascia forward to engage the fasten-
ers.
(4) Install push pins attaching top of fascia to
body.
(5) Install nut on fascia stud. and install tail lamp
housing (300M).
(6) Install trunk carpet back in position.
(7) Install fasteners attaching fascia to rear quar-
ter panel and splash shields.
REAR BUMPER FASCIA – INTREPID
REMOVAL
(1) Open deck lid and remove tail lamps.
(2) Remove fasteners attaching fascia to rear quar-
ter and splash shields.
(3) Remove fasteners attaching fascia to tail lamp
can.
(4) Remove fasteners attaching fascia to lower
trunk panel.
(5) Pull sides of fascia outwards to disengage
snaps to quarter panel attaching bracket (Fig. 9).
(6) Pull fascia rearward to expose license plate
lamp wire connector. Disconnect wire harness connec-
tor. The connector is located on the left side of vehi-
cle.
Fig. 8 Rear Bumper Fascia
Fig. 7 Front Bumper Reinforcement
300M
FRAMES AND BUMPERS
13 - 3
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Connect the license plate lamp wire connector
to the body harness.
(2) Place rear fascia in position on vehicle, by fit-
ting foam to bumper beam.
(3) Install center fastener to lower trunk panel.
(4) Snap sides of fascia between quarter panel and
bracket.
(5) Install fasteners to tail lamp can.
(6) Install fasteners attaching fascia to rear quar-
ter panel and splash shields.
(7) Install the remaining fasteners to lower trunk
panel.
(8) Install tail lamps.
REAR BUMPER REINFORCEMENT
REMOVAL
(1) Remove rear fascia.
(2) Remove attaching bolts and nuts from attach-
ing bracket to rails (Fig. 10).
INSTALLATION
(1) Place reinforcement in position on rear of vehi-
cle.
(2) Install bracket to rails attaching bolts and
nuts.
Fig. 9 Rear Bumper Fascia
Fig. 10 Rear Bumper Reinforcement
13 - 4
FRAMES AND BUMPERS
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст