Chrysler New Yorker. Manual — part 620

TEST TC-103A

REPAIRING - 1/1 O2S HEATER FAILURE

Perform TEST DTC Before Proceeding

1/1 RIGHT BANK UP

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

316

TEST TC-103A

REPAIRING - 1/1 O2S HEATER FAILURE

Perform TEST DTC Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

ARE THERE ANY

REFER TO "DTC

START TEST WITH THE DRB, READ

OTHER "1/1 O2

YES

TEST" TO PERFORM

TC-103A. ALL TROUBLE CODES.

SENSOR" RELATED

THE APPROPRIATE

TROUBLE CODES? OXYGEN

SENSOR

TEST.

NO

TURN IGNITION OFF.

WAIT 8 MINUTES.

(ENGINE OFF)

IGNITION ON.

WAIT FOR THE VOLTAGE

WITH THE DRB IN

READING TO STABILIZE

SENSORS, MONITOR

THE O2 SENSOR

VOLTAGE. BETWEEN 0.4 AND 0.6V

WITH THE DRB IN

MONITOR THE

IS THE

ACTUATOR TESTS,

1/1 O2 SENSOR

1/1 O2 SENSOR

YES

CONTINUE TEST

PERFORM THE 1/1 O2 VOLTAGE FOR TWO

VOLTAGE STILL

TC-103A ON

THE

SENSOR HEATER

MINUTES.

BETWEEN 0.4 AND

NEXT PAGE.

TEST.

0.6V?

NO

DID YOU COME FROM

YES

CONTINUE TEST

TEST TC-118A?

TC-118A.

NO

AT THIS TIME, THE
CONDITION REQUIRED

STOP ALL ACTUATOR

TO SET THE TROUBLE

TESTS.

CODE IS NOT

TEST COMPLETE.*

PRESENT.

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

317

TEST TC-103A

CONTINUED - REPAIRING - 1/1 O2S HEATER FAILURE

1/1 RIGHT BANK UP

FIG. 1

1/1 RIGHT BANK UP

FIG. 2

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

318

TEST TC-103A

CONTINUED - REPAIRING - 1/1 O2S HEATER FAILURE

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

TEST TC-103A

DISCONNECT THE

IS ANY TERMINAL

CONTINUED FROM

1/1 O2 SENSOR

CORRODED, DAMAGED,

YES

REPAIR OR REPLACE

THE PREVIOUS

HARNESS CONNECTOR.**

PUSHED OUT OR

AS NECESSARY.*

PAGE MISWIRED?

SEE GENERAL INFO 4.4

NO

NOTE:

USING A VOLTMETER, CHECK FUSES OR

THE DRB IS STILL

MEASURE THE ASD

IS THE VOLTAGE

NO

REPAIR THE OPEN

ACTUATING THE O2 RELAY OUTPUT

ABOVE 10.5

VOLTS?

ASD RELAY OUTPUT

SENSOR HEATER

CIRCUIT.

CIRCUIT.*

TEST.

FIG. 1

YES

STOP ALLOW THE 1/1 O2

SENSOR

ALL ACTUATOR

TO COOL TO ROOM

TEMPERATURE.

TESTS.

USING AN OHMMETER,

MEASURE THE O2 IS

THE RESISTANCE

NO

REPLACE THE 1/1 O2

SENSOR HEATER

BETWEEN 4.0 AND

SENSOR.*

ELEMENT TERNINALS

7.0 OHMS?

1 AND 2. FIG. 2

YES

USING AN OHMMETER,

CIRCUIT TO GROUND.

IS THE RESISTANCE

NO

REPAIR THE OPEN

MEASURE FROM THE

BELOW 5.0 OHMS?

1/1 O2 SENSOR

HEATER GROUND...

FIG. 1

GROUND CIRCUIT.*

YES

REPLACE THE 1/1 O2

SENSOR.*

T

R

O

U
B

L

E

C

O

D

E

T

E
S

T

S

319