Chrysler New Yorker. Manual — part 317
INSTALLATION
(1) Place latch in position.
(2) Install screws to attach latch to console.
(3) Check operation of latch.
CENTER CONSOLE ARMREST LID
REMOVAL
(1) Open armrest lid.
(2) Remove lid attaching screws.
(3) Remove lid from console.
INSTALLATION
(1) Place lid in position.
(2) Install screws to attach lid to console.
(3) Check operation of lid.
CENTER CONSOLE SHIFT BEZEL
REMOVAL
(1) Place gear selector in neutral.
(2) Loosen set screw attaching gear shift knob to
gear shift.
(3) Remove gear shift knob from gear shift.
(4) Disengage clips attaching bezel to center con-
sole (Fig. 8), or (Fig. 9).
(5) Disconnect the ash tray light and power outlet,
if equipped.
(6)
Disconnect the transmission range indicator
illumination connector.
(7) Remove bezel from vehicle.
INSTALLATION
(1) Connect the transmission range indicator illu-
mination connector.
(2) Connect the transmission indicator lamp. Con-
nect ash tray light, if equipped.
(3) Place bezel in position on vehicle.
(4) Engage clips attaching bezel to center console.
(5) Push gear shift knob onto gear shift.
(6) Tighten set screw attaching gear shift knob to
gear shift.
CENTER CONSOLE CUP HOLDER ASSEMBLY
REMOVAL
(1) Remove center console shift bezel (Fig. 8), or
(Fig. 9).
(2) Raise console armrest lid.
(3) Remove screws at top and bottom of cup holder
assembly (Fig. 10).
(4) Lift up and forward to remove assembly.
INSTALLATION
(1) Place cup holder into center console and align
screw holes.
(2) Install upper and lower screws.
(3) Lower console armrest lid.
(4) Install center console shift bezel.
CENTER CONSOLE SIDE PANELS – CONCORDE/
LHS
REMOVAL
(1) Move seats to the full rear position.
(2) Remove center console shift bezel (Fig. 8).
(3) Disengage clips from center console (Fig. 5).
(4) Remove side panels.
INSTALLATION
(1) Place center console side panels in position on
vehicle.
(2) Press side panel to seat clips.
(3) Install center console shift bezel.
Fig. 7 Center Console
300M
BODY
23 - 9
REMOVAL AND INSTALLATION (Continued)
CENTER CONSOLE SIDE PANELS – INTREPID,
LHS, 300M
REMOVAL
(1) Move seats to the full rear position.
(2) Remove center console bezel (Fig. 9).
(3) Remove steering column cover.
(4) Remove fasteners from the side panels (Fig. 6).
(5) Disengage side panel clips from center console.
(6) Remove side panels.
INSTALLATION
(1) Place center console side panels in position on
vehicle.
(2) Press on side panel to seat clips.
(3) Install fasteners to side panels.
(4) Install steering column cover.
(5) Install center console shift bezel.
Fig. 8 Center Console Bezel – Concorde
Fig. 9 Center Console Bezel – Intrepid Shown – LHS/300M Similar
23 - 10
BODY
300M
REMOVAL AND INSTALLATION (Continued)
CENTER CONSOLE REAR BEZEL
REMOVAL
(1) Disengage tabs on sides at bottom (Fig. 11).
(2) Open arm rest lid and remove rear bezel
attaching screws.
(3) Remove rear bezel.
INSTALLATION
(1) Align rear bezel in position on console.
(2) Install rear bezel attaching screws.
(3) Push forward at the bottom to lock tabs in
position.
CROSS CAR BEAM
REMOVAL
(1) Remove steering column and instrument panel
from vehicle.
(2) Remove fasteners attaching cross car beam to
plenum in both locations (Fig. 12).
(3) Remove left side fasteners attaching the cross
car beam to cowl side panel.
(4) Remove right side fasteners attaching the cross
car beam to cowl side panel.
(5) Remove cross car beam from vehicle.
INSTALLATION
(1) Place cross car beam in position in vehicle.
(2) Install right side fasteners attaching the cross
car beam to cowl side panels.
(3) Install left side fasteners attaching the cross
car beam to cowl side panels.
(4) Install fasteners to plenum in both locations.
(5) Install steering column and instrument panel.
COWL SCREEN
REMOVAL
(1) Release hood latch and open hood.
(2) Remove wiper arms. Refer to Group 8K, Wind-
shield Wiper and Washer Systems.
(3) Remove screws attaching cowl screen at the
windshield and under hood (Fig. 13).
(4) Remove cowl screen from vehicle.
INSTALLATION
(1) Place cowl screen in position on vehicle.
(2) Install cowl screen screws, starting at fender
moving inboard.
(3) Install wiper arms. Refer to Group 8K, Wind-
shield Wiper and Washer Systems.
DECK LID LATCH
REMOVAL
(1) Open deck lid.
(2) Remove fasteners attaching deck lid lining to
rear of deck lid.
(3) Remove bolts attaching deck lid latch to deck
lid (Fig. 14), (Fig. 15) or (Fig. 16).
(4) Remove deck lid latch from deck lid.
(5) Disconnect power lock connector from latch
solenoid.
(6) Disconnect deck lid ajar switch connector from
latch.
(7) Remove latch from vehicle.
INSTALLATION
(1) Place latch in position on vehicle.
(2) Connect deck lid ajar switch connector on latch.
(3) Connect power lock connector on latch solenoid.
(4) Place deck lid latch in position on deck lid.
(5) Install bolts to attach deck lid latch to deck lid.
(6) Adjust deck lid latch for proper deck lid to
quarter panel alignment and weatherstrip sealing.
(7) Install fasteners to attach deck lid lining to
rear of deck lid.
(8) Verify deck lid latch operation.
Fig. 10 Center Console Cup Holder Assembly
Fig. 11 Center Console Rear Bezel
300M
BODY
23 - 11
REMOVAL AND INSTALLATION (Continued)
DECK LID
REMOVAL
(1) Release deck lid latch and open deck lid.
(2) Mark bolt locations on inside of deck lid to aid
installation.
Fig. 12 Cross Car Beam
Fig. 13 Cowl Screen
Fig. 14 Deck Lid Latch – Concorde/LHS
23 - 12
BODY
300M
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст