RAM Cargo Van (2015 year). Manual — part 39
Cavity
Cartridge Fuse
Mini-Fuse
Description
M25
–
20 Amp Yellow
Fuel Pump, Diesel Lift Pump – If Equipped
M26
–
10 Amp Red
Power Mirror Switch, Driver Window Switch
M27
–
10 Amp Red
Wireless Control Module,
Keyless Entry Module
M28
–
10 Amp Red
Powertrain, Transmission Control Module
M29
–
10 Amp Red
Occupant Classification Module
M30
–
15 Amp Blue
Rear Wiper Module, Power Folding Mirror
M31
–
20 Amp Yellow
Back-Up Lamps
M32
–
10 Amp Red
Airbag Module, THATCHUM – If Equipped
M33
–
10 Amp Red
Powertrain
M34
–
10 Amp Red
Park Assist, Heater Climate Control Module,
Headlamp Wash, Compass, Rear Camera,
Door Lamps, Flashlight, Relay Diesel Cabin
Heater, Rad Fan Diesel – If Equipped
616
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Cavity
Cartridge Fuse
Mini-Fuse
Description
M35
–
10 Amp Red
Heated Mirrors
M36
–
20 Amp Yellow
Power Outlet #3 (Instrument Panel or with
Console Center)
M37
–
10 Amp Red
Antilock Brakes, Stability Control, Stop Lamp,
Fuel Pump
M38
–
25 Amp Clear
Door Lock/Unlock Motors, Liftgate Lock/
Unlock Motors
The power windows are fused by a 25 Amp circuit
breaker located in the Totally Integrated Power Module.
VEHICLE STORAGE
If you are leaving your vehicle dormant for more than 21
days, you may want to take steps to protect your battery.
You may do the following:
• Remove the 60 Amp cartridge in the Totally Integrated
Power Module (TIPM) labeled Ignition-Off Draw (IOD).
• Or, disconnect the negative cable from the battery.
• Anytime you store your vehicle, or keep it out of
service for two weeks or more, run the air conditioning
system at idle for about five minutes in the fresh air
and high blower setting. This will ensure adequate
system lubrication to minimize the possibility of com-
pressor damage when the system is started again.
7
MAINTAINING YOUR VEHICLE
617
-------------------------------------------------------------------------------------------------------------------------------------------------------------
REPLACEMENT BULBS
Interior Bulbs
Bulb Number
Center & Rear Dome Lamp
578
Center & Rear Reading Lamps
578
Front Door Courtesy Lamp
578
Front Header Reading Lamps – If Equipped
578
Instrument Cluster Lamps
PC74
Liftgate Lamp(s)
578
Overhead Console Reading Lamps
PC579
Removable Console Lamp – If Equipped
194
Visor Vanity Lamps
6501966
NOTE:
For lighted switches, see your authorized dealer
for replacement instructions.
618
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Exterior Bulbs
Bulb Number
Headlamp
H11LL
Fog Lamp – If Equipped
PSX24W
Front Side Marker, Park/Turn Signal
3757A or PY27/7W
Rear Tail, Stop, Turn Signal Lamp
LED (Serviced at Authorized Dealer)
Center High-Mounted Stop Lamp
LED (Serviced at Authorized Dealer)
Backup Lamp
3157
License
168
NOTE:
All of the interior bulbs are glass wedge base or
glass cartridge types. Aluminum base bulbs are not
approved and should not be used for replacement.
7
MAINTAINING YOUR VEHICLE
619
-------------------------------------------------------------------------------------------------------------------------------------------------------------
BULB REPLACEMENT
NOTE:
Lens fogging can occur under certain atmo-
spheric conditions. This will usually clear as atmospheric
conditions change to allow the condensation to change
back into a vapor. Turning the lamps on will usually
accelerate the clearing process.
Headlamps
1. Raise the hood to access the rear of the headlamp
housing.
2. Slide the red lock tab rearward on the connector, then
depress the tab and remove the connector from the
bulb.
3. Twist the headlamp bulb and pull the bulb from the
headlamp housing.
4. Install the new headlamp bulb and twist until locked
into the headlamp housing.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
5. Connect the wiring connector to bulb and slide red
lock tab forward.
620
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Front Park/Turn Signal Lamps
1. Raise the hood to access the rear of the headlamp
housing.
2. Twist the turn signal socket and remove from the
headlamp housing, then pull the bulb out.
3. Push the new bulb into the socket and reinstall the
socket by twisting until locked into the headlamp
housing.
Fog Lamps
NOTE:
Access to the fog lamp bulb is from the rear of
the fascia. On the left rear side of the fascia, remove the
push pin and lower the hinged access door on the air
dam.
1. From behind the bumper fascia, or the access panel on
the air dam, squeeze the two tabs on the side of the
bulb socket and pull straight out from the fog lamp.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with an oily surface, clean the
bulb with rubbing alcohol.
2. Disconnect the wire harness from the bulb.
3. Reconnect the wiring harness to the new bulb and
reinstall by inserting the new bulb straight into the fog
lamp until it locks into place.
7
MAINTAINING YOUR VEHICLE
621
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Rear Tail, Stop, Turn Signal, Side Marker And
Backup Lamps
1. Raise the liftgate.
2. Remove the tail lamp assembly by removing the two
screws from the inboard side. Use a fiber stick or
similar tool to gently pry the light on the outboard side
to disengage the two ball studs.
Tail Lamp Assembly Screws
622
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTE:
• If a screwdriver is used, make sure a soft material is
placed between the vehicle body and tool so not to
scratch the paint.
• The PRY location is best closest to the studs while
dislodging them separately.
3. Twist the socket and remove from the lamp assembly.
4. Pull the bulb to remove it from the socket.
5. Replace the bulb, reinstall the socket, and reattach the
lamp assembly.
Center High-Mounted Stop Lamp (CHMSL)
The CHMSL uses LED lamps that are not serviceable
separately. The CHMSL must be replaced as an assembly.
See your authorized dealer.
License Lamp
The license plate lamp is located under the tailgate light
bar and above the license plate.
1. Using a small screwdriver, press inward the locking
tab on the outboard side of the lamp assembly and
pull down on the lamp assembly for removal.
2. Twist and remove the socket from the lamp assembly
and pull the bulb out to remove.
3. Push the bulb into the socket, twist the socket into the
lamp assembly and reinstall the lamp assembly into
place ensuring the locking tab is secure.
7
MAINTAINING YOUR VEHICLE
623
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FLUID CAPACITIES
U.S.
Metric
Fuel (Approximate)
20 Gallons
76 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-20,
API Certified).
6 Quarts
5.6 Liters
Cooling System *
3.6L Engine (MOPAR® Antifreeze/
Engine Coolant 10 Year/150,000 Mile
Formula or equivalent) meeting the
requirements of Chrysler Material
Standard MS.90032.
13.4 Quarts
12.6 Liters
* Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear
heater.
624
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
FLUIDS, LUBRICANTS AND GENUINE PARTS
Engine
Component
Fluid, Lubricant, or Genuine Part
Engine Coolant
We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula
OAT (Organic Additive Technology) meeting the requirements of Chrysler Material
Standard MS.90032.
Engine Oil
We recommend you use API Certified SAE 5W-20 Engine Oil, meeting the require-
ments of Chrysler Material Standard MS-6395 such as MOPAR®, Pennzoil®, and
Shell Helix®. Refer to your engine oil filler cap for correct SAE grade.
Engine Oil Filter
We recommend you use MOPAR® Engine Oil Filters.
Spark Plugs
We recommend you use MOPAR® Spark Plugs.
Fuel Selection
87 Octane
7
MAINTAINING YOUR VEHICLE
625
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CAUTION!
• Mixing of engine coolant (antifreeze) other than
specified Organic Additive Technology (OAT) en-
gine coolant (antifreeze), may result in engine
damage and may decrease corrosion protection.
Organic Additive Technology (OAT) engine cool-
ant is different and should not be mixed with
Hybrid Organic Additive Technology (HOAT) en-
gine coolant (antifreeze) or any “globally compat-
ible” coolant (antifreeze). If a non-OAT engine
coolant (antifreeze) is introduced into the cooling
system in an emergency, the cooling system will
need to be drained, flushed, and refilled with fresh
OAT coolant (conforming to MS.90032), by an au-
thorized dealer as soon as possible.
(Continued)
CAUTION! (Continued)
• Do not use water alone or alcohol-based engine
coolant (antifreeze) products. Do not use additional
rust inhibitors or antirust products, as they may not
be compatible with the radiator engine coolant and
may plug the radiator.
• This vehicle has not been designed for use with
propylene glycol-based engine coolant (antifreeze).
Use of propylene glycol-based engine coolant (an-
tifreeze) is not recommended.
626
MAINTAINING YOUR VEHICLE
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Chassis
Component
Fluid, Lubricant, or Genuine Part
Automatic Transmission
Use Only ATF+4® Automatic Transmission Fluid. Fail-
ure to use ATF+4® fluid may affect the function or
performance of your transmission. We recommend
MOPAR® ATF+4® Fluid.
Brake Master Cylinder
We recommend you use MOPAR® DOT 3. If DOT 3
brake fluid is not available, then DOT 4 is acceptable.
Power Steering Reservoir
We recommend you use MOPAR® Power Steering Fluid
+4, MOPAR® ATF+4® Automatic Transmission Fluid.
7
MAINTAINING YOUR VEHICLE
627
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE SCHEDULE
Your vehicle is equipped with an automatic oil change
indicator system. The oil change indicator system will
remind you that it is time to take your vehicle in for
scheduled maintenance.
Based on engine operation conditions, the oil change
indicator message will illuminate. This means that ser-
vice is required for your vehicle. Operating conditions
such as frequent short-trips, trailer tow, extremely hot or
cold ambient temperatures, and E85 fuel usage will
influence when the “Oil Change Required” message is
displayed. Severe Operating Conditions can cause the
change oil message to illuminate as early as 3,500 miles
(5,600 km) since last reset. Have your vehicle serviced as
soon as possible, within the next 500 miles (805 km).
Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change. If a
scheduled oil change is performed by someone other
than your authorized dealer, the message can be reset by
referring to the steps described under “Electronic Vehicle
Information Center (EVIC)” in “Understanding Your
Instrument Panel” for further information.
NOTE:
Under no circumstances should oil change inter-
vals exceed 10,000 miles (16,000 km) or twelve months,
whichever comes first.
Severe Duty All Models
Change Engine Oil at 4000 miles (6,500 km) if the vehicle
is operated in a dusty and off road environment. This
type of vehicle use is considered Severe Duty.
Once A Month Or Before A Long Trip:
• Check engine oil level.
• Check windshield washer fluid level.
• Check tire pressure and look for unusual wear or damage.
Rotate tires at the first sign of irregular wear, even if it
occurs before the oil indicator system turns on.
630
MAINTENANCE SCHEDULES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
• Check the fluid levels of the coolant reservoir, brake
master cylinder, and power steering and fill as needed.
• Check function of all interior and exterior lights.
Required Maintenance Intervals
.
Refer to the maintenance schedules on the following
page for the required maintenance intervals.
At Every Oil Change Interval As Indicated By Oil Change Indicator System:
• Change oil and filter.
• Rotate the tires. Rotate at the first sign of irregular wear, even if it occurs before the oil indicator system
turns on.
• Inspect battery and clean and tighten terminals as required.
• Inspect brake pads, shoes, rotors, drums, hoses and park brake.
• Inspect engine cooling system protection and hoses.
• Inspect exhaust system.
• Inspect engine air cleaner if using in dusty or off-road conditions.
8
MAINTENANCE SCHEDULES
631
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Maintenance Chart
Refer to the Maintenance Schedules on the following
pages for the required maintenance intervals.
Mileage or time passed
(whichever comes first)
20,000
30,000
40,000
50,000
60,000
70,000
80,000
90,000
100,000
1
10,000
120,000
130,000
140,000
150,000
Or Years:
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Or Kilometers:
32,000
48,000
64,000
80,000
96,000
1
12,000
128,000
144,000
160,000
176,000
192,000
208,000
224,000
240,000
Additional Inspections
Inspect the CV joints.
X
X
X
X
X
Inspect front suspension, tie rod
ends, boot seals, and replace if
necessary.
X
X
X
X
X
X
X
Inspect the brake linings, replace
as necessary.
X
X
X
X
X
X
X
632
MAINTENANCE SCHEDULES
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Mileage or time passed
(whichever comes first)
20,000
30,000
40,000
50,000
60,000
70,000
80,000
90,000
100,000
1
10,000
120,000
130,000
140,000
150,000
Or Years:
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Or Kilometers:
32,000
48,000
64,000
80,000
96,000
1
12,000
128,000
144,000
160,000
176,000
192,000
208,000
224,000
240,000
Additional Maintenance
Replace engine air filter.
X
X
X
X
X
Replace cabin/air conditioning
filter.
X
X
X
X
X
X
X
Replace spark plugs
(3.6L engine). **
X
Flush and replace the engine
coolant at 10 years or
150,000 miles (240,000 km)
whichever comes first.
X
X
8
MAINTENANCE SCHEDULES
633
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст