Chrysler 300 (2019 year). Manual — part 27
Display
After pressing the “Display” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Display Mode
Auto
Manual
Display Brightness With Headlights
ON
+
–
NOTE:
• When in the “Display Brightness With Headlights ON” display, you may select the brightness with the headlights
on.
• To make changes to the ⬙Display Brightness with Headlights ON⬙ setting, the headlights must be on and the inte-
rior dimmer switch must not be in the
⬙party⬙ or ⬙parade⬙ positions.
Display Brightness With Headlights
OFF
+
–
NOTE:
• When in the “Display Brightness With Headlights OFF” display, you may select the brightness with the headlights
off. Adjust the brightness from (1–10) with the “+” and “–” buttons on the touchscreen.
• To make changes to the ⬙Display Brightness with Headlights OFF⬙ setting, the headlights must be off and the inte-
rior dimmer switch must not be in the
⬙party⬙ or ⬙parade⬙ positions.
10
MULTIMEDIA
425
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
Set Theme
List Of Options
NOTE:
When in the “Set Theme” display, you may select the theme for the display screen. To make your selection, press the
⬙Set Theme⬙ button on the touchscreen, then select the desired theme option button until a check-mark appears show-
ing that the setting has been selected.
Touchscreen Beep
On
Off
Controls Screen Time-Out — If
Equipped
On
Off
NOTE:
When the “Control Screen Time Out” feature is selected, the controls screen will stay open for five seconds before the
screen times out. With the feature deselected, the screen will stay open until it is manually closed.
Navigation Next Turn Pop-ups Dis-
played In Cluster — If Equipped
On
Off
NOTE:
When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in-
strument cluster display as the vehicle approaches a designated turn within a programmed route.
426
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Units
After pressing the “Units” button on the touchscreen, you may select each unit of measure independently displayed in the
instrument cluster display, and navigation system (if equipped). The following selectable units of measure are listed below:
Setting Name
Selectable Options
Units
US
Metric
Custom
NOTE:
The “Custom” option allows you to set the “Speed” (MPH, or km/h), “Distance” (mi, or km), “Fuel Consumption”
[MPG (US), MPG (UK), L/100 km, or km/L], “Pressure” (psi, kPa, or bar), and “Temperature” (°C, or °F) units of
measure independently.
Voice
After pressing the “Voice” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Voice Response Length
Brief
Detailed
Show Command List
Never
w/Help
Always
10
MULTIMEDIA
427
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Clock
After pressing the “Clock” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Sync Time With GPS — If
Equipped
On
Off
NOTE:
The “Sync Time With GPS” feature will allow you to automatically have the radio set the time.
Set Time Hours
+
–
Set Time Minutes
+
–
Time Format
12 hrs
24 hrs
AM
PM
Show Time In Status Bar — If
Equipped
On
Off
NOTE:
The “Show Time In Status Bar” feature will allow you to turn on or shut off the digital clock in the status bar.
428
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Safety & Driving Assistance
After pressing the “Safety & Driving Assistance” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Forward Collision Warn-
ing — If Equipped
On
Off
NOTE:
Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in
front of you.
The FCW system state is kept in memory from one ignition cycle to the next. If the system is turned OFF, it will re-
main off when the vehicle is restarted.
Forward Collision Warn-
ing Sensitivity — If
Equipped
Near
Far
NOTE:
The Forward Collision Warning (FCW) feature provides an audible and/or visual warning to potential forward colli-
sions. The feature can be can be set to “Far”, or set to “Near”. The default status of FCW is the “Far” setting. This
means the system will warn you of a possible collision with the vehicle in front of you when you are farther away.
This gives you the most reaction time. To change the setting for more dynamic driving, select the “Near” setting. This
warns you of a possible collision when you are much closer to the vehicle in front of you.
10
MULTIMEDIA
429
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
Forward Collision Warn-
ing (FCW) — Active Brak-
ing
On
Off
NOTE:
The FCW system includes Advanced Brake Assist (ABA). When this feature is selected, the ABA applies additional
brake pressure when the driver requests insufficient brake pressure to avoid a potential frontal collision. The ABA
system becomes active at 5 mph (8 km/h). To make your selection, press the “Forward Collision Warning Active
Braking” button on the touchscreen, until a check-mark appears next to setting, indicating that the setting had been
selected.
LaneSense Warning — If
Equipped
Early
Medium
Late
NOTE:
When the “LaneSense Warning” feature is selected, it sets the distance at which the steering wheel will provide feed-
back for potential lane departures.
LaneSense Strength — If
Equipped
Low
Medium
High
NOTE:
When the “LaneSense Strength” feature is selected, it sets the strength of the steering wheel feedback for potential
lane departures.
430
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
ParkSense — If Equipped
Sound Only
Sound & Display
NOTE:
The ParkSense system will scan for objects behind the vehicle when the gear selector is in REVERSE and the vehicle
speed is less than 11 mph (18 km/h). It will provide an alert (audible and/or visual) to indicate the proximity to
other objects. The system can be enabled with Sound Only, or Sound and Display. To change the ParkSense status,
press and release the “Sound Only” or “Sound and Display” button.
Front ParkSense Volume
Low
Medium
High
NOTE:
The Front ParkSense Chime Volume settings can be selected from the Uconnect System. The chime volume settings
include Low, Medium, and High. The factory default volume setting is Medium. ParkSense will retain its last known
configuration state through ignition cycles.
Rear ParkSense Volume
Low
Medium
High
NOTE:
The Rear ParkSense Chime Volume settings can be selected from the Uconnect System. The chime volume settings
include Low, Medium, and High. ParkSense will retain its last known configuration state through ignition cycles.
Electric Power Steering
Default — If Equipped
Normal
Sport
Comfort
NOTE:
When the “Electric Power Steering Default” is selected, it allows you to change the default setting of your vehicle to
either normal, sport, or comfort.
10
MULTIMEDIA
431
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
Blind Spot Alert — If
Equipped
Off
Lights
Lights & Chime
NOTE:
• When this feature is selected, the Blind Spot Alert feature Provides alerts, visual and/or audible, to indicate objects
in your blind spot. The Blind Spot Alert feature can be activated in “Lights” mode. When this mode is selected, the
Blind Spot Monitor (BSM) system is activated and will only show a visual alert in the exterior mirrors. When
“Lights & Chime” mode is activated, the Blind Spot Monitor (BSM) will show a visual alert in the exterior mirrors
as well as an audible alert when the turn signal is on.
• If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not dam-
aged, the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor align-
ment. Having a sensor that is misaligned will result in the BSM not operating to specification.
ParkView Backup Camera
Delay
On
Off
NOTE:
When the vehicle is shifted out of REVERSE (with camera delay turned off), the rear camera mode is exited and the
previously viewed screen appears again. When the vehicle is shifted out of REVERSE (with camera delay turned on),
the rear view image with dynamic grid lines will be displayed for up to ten seconds after shifting out of “REVERSE”
unless the forward vehicle speed exceeds 8 mph (13 km/h), the transmission is shifted into “PARK” or the ignition is
switched to the OFF position.
432
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
ParkView Backup Camera
Active Guidelines
On
Off
NOTE:
Your vehicle may be equipped with the ParkView Rear Back Up Camera Active Guidelines that allows you to see ac-
tive guidelines over the ParkView Back up camera display whenever the gear selector is put into REVERSE. The im-
age will be displayed on the radio touchscreen display along with a caution note to “check entire surroundings”
across the top of the screen. After five seconds, this note will disappear.
Hill Start Assist — If
Equipped
On
Off
NOTE:
When this feature is selected, the Hill Start Assist (HSA) system is active.
Paddle Shifters— If
Equipped
On
Off
10
MULTIMEDIA
433
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Mirrors & Wipers
After pressing the “Mirrors and Wipers” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Headlights With Wipers
On
Off
Rain Sensing Auto Wipers
On
Off
NOTE:
When this feature is selected and the wipers are on, the system will automatically activate the windshield wipers if it
senses moisture on the windshield.
Tilt Side Mirrors in Reverse
On
Off
NOTE:
When the “Tilt Side Mirror In Reverse” feature is selected, the exterior sideview mirrors will tilt downward when the
ignition is in the RUN position and the transmission gear selector is in the REVERSE position. The mirrors will move
back to their previous position when the transmission is shifted out of REVERSE.
434
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lights
After pressing the “Lights” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Headlight Off Delay
0 sec
30 sec
60 sec
90 sec
Headlight Illumination On Ap-
proach
0 sec
30 sec
60 sec
90 sec
Headlights With Wipers — If
Equipped
On
Off
Auto Dim High Beams — If
Equipped
On
Off
Daytime Running Lights — If
Equipped
On
Off
Steering Directed Lights
On
Off
Flash Lights With Lock
On
Off
10
MULTIMEDIA
435
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Doors & Locks
After pressing the “Doors & Locks” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Auto Door Locks
On
Off
Auto Unlock On Exit
On
Off
NOTE:
When the “Auto Unlock On Exit” feature is selected, all doors will unlock when the vehicle is stopped, the transmis-
sion is in the PARK or NEUTRAL position and the driver’s door is opened.
Flash Lights With Lock
On
Off
NOTE:
When the “Flash Lights With Lock” feature is selected, the exterior lights will flash when the doors are locked or un-
locked with the key fob, or when using the passive entry feature. This feature may be selected with or without the
“Sound Horn With Lock” feature selected.
Sound Horn With Lock
Off
1st Press
2nd Press
Sound Horn With Remote
Start
On
Off
436
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
1st Press Of Key Fob Un-
locks
Driver Door
All Doors
NOTE:
• When ⬙Driver Door⬙ is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first
press of the key fob unlock button. You must press the key fob unlock button twice to unlock the passenger’s
doors. When
⬙All Doors⬙ is selected for 1st Press Of Key Fob Unlocks, all doors will unlock on the first press of the
key fob unlock button.
• If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock no matter which
Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks “Driver Door” is programmed,
only the driver’s door will unlock when the driver’s door is grasped. With Passive Entry, if 1st Press Of Key Fob
Unlocks “Driver Door” is programmed, touching the handle more than once will result in only the driver’s door
opening. If “Driver Door” is selected, once the driver door is opened, the interior door lock/unlock switch can be
used to unlock all doors (or use key fob).
Passive Entry — If
Equipped
On
Off
NOTE:
The “Passive Entry” feature allows you to lock and unlock the vehicles door(s) without having to push the key fob
lock or unlock buttons. To make your selection, press the “Passive Entry” button on the touchscreen, until a check-
mark appears next to the setting, showing that the setting has been selected.
10
MULTIMEDIA
437
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Setting Name
Selectable Options
Personal Settings Linked
To Key Fob — If
Equipped
On
Off
NOTE:
• This feature provides automatic recall of all settings stored to a memory location (driver’s seat, exterior mirrors,
steering column position and radio station pre-sets) to enhance driver mobility when entering and exiting the ve-
hicle.
• The seat returns to the memorized seat location (if “Personal Settings Linked to Key Fob” is set to on) when the
key fob is used to unlock the door.
Auto Comfort Systems — If Equipped
After pressing the “Auto-On Comfort” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Auto-On Driver Heated
Seat
Off
Remote Start
All Starts
NOTE:
When this feature is selected the driver’s heated seat and heated steering wheel will automatically turn on when tem-
peratures are below 40° F (4.4° C). When temperatures are above 80° F (26.7° C) the driver’s vented seat will turn on.
438
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Engine Off Options
After pressing the “Engine Off Options” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Easy Exit Seat — If Equipped
On
Off
NOTE:
When the “Easy Exit Seat” feature is selected, the driver’s seat will automatically move rearward once the engine is
shut off.
Engine Off Power Delay
0 sec
45 sec
5 mins
10 mins
NOTE:
When the “Engine Off Power Delay” feature is selected, the power window switches, radio, Uconnect Phone system
(if equipped), DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for
up to ten minutes after the ignition is cycled to OFF. Opening either front door will cancel this feature. To change the
Engine Off Power Delay setting, press the “+” or “-” button on the touchscreen to select your desired time interval,
and choose from “0 seconds,” “45 seconds,” “5 minutes” or “10 minutes.”
Headlight Off Delay
0
30
60
90
NOTE:
When the “Headlight Off Delay” feature is selected, the driver can choose to have the headlights remain on for 0, 30,
60, or 90 seconds when exiting the vehicle. To change the Headlight Off Delay status press the “+” or “–” button on
the touchscreen to select your desired time interval.
10
MULTIMEDIA
439
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Audio
After pressing the “Audio” button on the touchscreen, the following settings will be available:
Setting Name
Selectable Options
Balance/Fade
“Speaker” Icon
Arrow Buttons
NOTE:
The “Balance/Fade” feature allows you to adjust the Balance and Fade settings. Press and drag the speaker icon, use
the arrows to adjust, or tap the “Speaker” icon to readjust to the center.
Equalizer
+
–
NOTE:
• The “Equalizer” feature allows you to adjust the Bass, Mid, and Treble settings. Adjust the settings with the “+”
and “–” setting buttons on the touchscreen or by selecting any point on the scale between the “+” and “–” buttons
on the touchscreen.
• Bass/Mid/Treble allows you to simply slide your finger up or down to change the setting as well as press directly
on the desired setting.
Speed Adjusted Vol-
ume
Off
1
2
3
NOTE:
The “Speed Adjusted Volume” feature increases or decreases volume relative to vehicle speed. To change the Speed
Adjusted Volume press the “Off,” “1,” “2” or “3” button on the touchscreen.
440
MULTIMEDIA
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст