Chrysler Town, Dodge Caravan. Manual — part 614
TEST
ACTION
APPLICABILITY
2
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
NOTE: Visually inspect both the component and the PCM connectors. Look
for damaged, partially broken wires, and backed out or corroded terminals.
Ignition on, engine not running.
Measure the voltage on the (K2) ECT Signal circuit in the ECT Sensor harness
connector.
Is the voltage above 5.2 volts?
All
Yes
→ Repair the short to battery voltage in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Ignition on, engine not running.
With the DRBIII
t, read the ECT Sensor voltage.
Is the voltage above 4.6 volts?
All
Yes
→ Go To 4
No
→ Go To 7
4
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Using a jumper wire, jumper across the ECT Sensor harness connector.
Ignition on, engine not running.
With the DRBIII
t, read the ECT Sensor voltage.
Is the voltage below 1.0 volt?
All
Yes
→ Replace the ECT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K2) ECT Signal circuit from the ECT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the open in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
264
DRIVEABILITY - NGC
P0116-ENGINE COOLANT TEMPERATURE PERFORMANCE —
Continued
TEST
ACTION
APPLICABILITY
6
Turn the ignition off.
Disconnect the ECT harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K4) Sensor ground circuit from the ECT Sensor
harness connector to the appropriate terminal of special tool # 8815.
Is the resistance below 5.0 ohms?
All
Yes
→ NOTE: Before continuing, check the PCM harness connector
terminals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Repair the open in the (K4) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
7
Disconnect the ECT Sensor harness connector.
Turn the ignition off.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K2) ECT Signal circuit in the ECT
Sensor harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the short to ground in the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 8
8
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between the (K2) ECT Sensor Signal circuit and the (K4)
Sensor ground circuit at the ECT Sensor harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the (K4) Sensor ground shorted to the (K2) ECT Sensor
Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ NOTE: Before continuing, check the PCM harness connector
terminals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
265
DRIVEABILITY - NGC
P0116-ENGINE COOLANT TEMPERATURE PERFORMANCE —
Continued
Symptom:
P0117-ENGINE COOLANT TEMPERATURE SENSOR LOW
When Monitored and Set Condition:
P0117-ENGINE COOLANT TEMPERATURE SENSOR LOW
When Monitored:
With the ignition on. Battery voltage greater than 10 volts.
Set Condition:
The Engine Coolant Temperature (ECT) sensor circuit voltage at the PCM
is less than 0.0782 of a volt. One Trip Fault.
POSSIBLE CAUSES
ECT SENSOR VOLTAGE BELOW 1.0 VOLTS
ECT SENSOR INTERNAL FAILURE
(K2) ECT SIGNAL SHORTED TO GROUND
(K2) ECT SIGNAL SHORTED TO (K4) SENSOR GROUND CIRCUIT
PCM
TEST
ACTION
APPLICABILITY
1
Ignition on, engine not running.
With the DRBIII
t, read the ECT Sensor voltage.
Is the voltage below 1.0 volt?
All
Yes
→ Go To 2
No
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
2
Turn the ignition off.
Disconnect the ECT harness connector.
Ignition on, engine not running.
With the DRBIII
t, read ECT Sensor voltage.
Is the voltage between 4.8 and 5.2 volts?
All
Yes
→ Replace the ECT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between ground and the (K2) ECT Signal circuit in the ECT
Sensor harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the ground shorted to the (K2) ECT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 4
266
DRIVEABILITY - NGC
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the ECT Sensor harness connector.
Disconnect the PCM harness connector.
Measure the resistance between the (K2) ECT Sensor Signal circuit and the (K4)
Sensor ground circuit in the ECT Sensor harness connector.
Is the resistance below 100 ohms?
All
Yes
→ Repair the (K4) Sensor ground shorted to the (K2) ECT Sensor
Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
No
→ Go To 5
5
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.
267
DRIVEABILITY - NGC
P0117-ENGINE COOLANT TEMPERATURE SENSOR LOW —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст