Chrysler Town, Dodge Caravan. Manual — part 815
Symptom:
RIGHT LOW BEAM HEADLAMP CIRCUIT SHORTED TO VOLTAGE
POSSIBLE CAUSES
FRONT CONTROL MODULE
GROUND CIRCUIT OPEN
HIGH BEAM AND LOW BEAM DRIVERS CIRCUITS SHORTED TOGETHER
RIGHT HEADLAMP
RIGHT LOW BEAM DRIVER CIRCUIT SHORTED TO VOLTAGE
WIRING PROBLEM
WIRING HARNESS INSPECTION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, erase the Front Control Module DTC’s.
Turn the headlamps on.
Switch the headlamps between high beam and low beam several times, pausing for
5 seconds in each position.
With the DRB, read Front Control Module DTC’s.
Is this DTC present?
All
Yes
→ Go To 2
No
→ Go To 7
2
Turn the ignition off.
Disconnect the Right Headlamp harness connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Right Headlamp harness connector.
Disconnect the Front Control Module.
Measure the resistance between the Right High Beam Driver circuit and the Right
Low Beam Driver circuit at the Right Headlamp harness connector.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Right High Beam Driver circuit for a short to the Right
Low Beam Driver circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
496
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Right Headlamp harness connector.
Disconnect the Front Control Module.
Turn the ignition on.
Measure the voltage of the Right Low Beam Driver circuit.
Is the voltage below 1.0 volt?
All
Yes
→ Go To 5
No
→ Repair the Right Low Beam Driver circuit for a short to voltage.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Turn the Headlamps off.
Install a substitute Headlamp Bulb in place of the Right Headlamp Bulb.
Turn the ignition on.
With the DRB, erase the Front Control Module DTC’s.
Turn the headlamps on.
Switch the headlamps between high beam and low beam several times, pausing for
5 seconds in each position.
With the DRB, read Front Control Module DTC’s.
Does the DRB display this DTC?
All
Yes
→ Go To 6
No
→ Replace the original Right Headlamp Bulb.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Inspect the wiring and connectors associated with the Right Low Beam Driver
circuit.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
7
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
Note: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
497
EXTERIOR LIGHTING
RIGHT LOW BEAM HEADLAMP CIRCUIT SHORTED TO VOLTAGE —
Continued
Symptom:
RIGHT REAR TURN SIGNAL OUTPUT OPEN
When Monitored and Set Condition:
RIGHT REAR TURN SIGNAL OUTPUT OPEN
When Monitored:
Ignition On.
Set Condition:
When output voltage status is LOW.
POSSIBLE CAUSES
INTERMITTENT CONDITION
GROUND CIRCUIT
TURN SIGNAL LAMP
RIGHT REAR TURN SIGNAL DRIVER CIRCUIT OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all BCM DTC’s.
Actuate the Turn Signals.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Right Rear Turn Signal Output Open?
All
Yes
→ Go To 2
No
→ The condition that caused the symptom is currently not present.
Inspect the related wiring for a possible intermittent condition.
Look for any chafed, pierced,pinched, or partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Right Rear Turn Signal harness connector.
Using a 12-volt test light connected to 12-volts, check the ground circuit.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Ground Circuit.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Right Rear Turn Signal Lamp connector.
Turn the ignition on.
Turn the Right Turn Signal on.
Using a 12-volt test light connected to ground, check the Right Rear Turn Signal
Output circuit.
Does the test light illuminate brightly?
All
Yes
→ Replace the Turn Signal Lamp.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
498
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Body Control Module C2 connector.
Measure the resistance of the Right Rear Turn Signal Driver Circuit to ground.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Right Rear Turn Signal Driver Circuit for an open
condition.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
499
EXTERIOR LIGHTING
RIGHT REAR TURN SIGNAL OUTPUT OPEN —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст