Chrysler Town, Dodge Caravan. Manual — part 859
Symptom:
EEPROM REFRESH FAILURE
When Monitored and Set Condition:
EEPROM REFRESH FAILURE
When Monitored:
With the ignition in the on position.
Set Condition:
The Memory Seat Mirror Module has a internal EEPROM failure.
POSSIBLE CAUSES
EEPROM REFRESH FAILURE
TEST
ACTION
APPLICABILITY
1
If there are no possible causes remaining, view repair.
All
Repair
Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
672
MEMORY SEAT
Symptom:
FRONT RISER DOWN POSITION STUCK
When Monitored and Set Condition:
FRONT RISER DOWN POSITION STUCK
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
If the seat switch is active for 30 seconds, this code will set and the
Memory Seat Mirror Module will ignore the input until the state has changed. Three
seconds after the stuck condition is removed, the seat will resume to normal operation.
Code will remain for 50 ignition cycles.
POSSIBLE CAUSES
STORED DIAGNOSTIC TROUBLE CODE
POWER SEAT SWITCH
SEAT FRONT DOWN SWITCH SENSE WIRE SHORT TO VOLTAGE
MEMORY SEAT MIRROR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Memory Seat Mirror Module.
Operate the driver’s power seat and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRB check for the same DTC to reset in the MSMM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Disconnect the Power Seat Switch connector.
Measure the voltage of the Seat Front Down Switch Sense circuit.
Is there any voltage present?
All
Yes
→ Go To 3
No
→ Replace the Power Seat Switch.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
3
Disconnect the Power Seat Switch connector.
Disconnect the Memory Seat Mirror Module C1 connector.
Turn the ignition on.
Measure the voltage of the Seat Front Down Switch Sense circuit to ground..
Is there any voltage present?
All
Yes
→ Repair the Seat Front Down Switch Sense wire for a short to
voltage.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 4
673
MEMORY SEAT
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
674
MEMORY SEAT
FRONT RISER DOWN POSITION STUCK —
Continued
Symptom:
FRONT RISER SENSOR OUT OF RANGE HIGH
When Monitored and Set Condition:
FRONT RISER SENSOR OUT OF RANGE HIGH
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
This condition is immediately set when the seat motor potentiometer
feeds a value higher than the Memory Seat Mirror Module has stored in EEPROM. Code
will remain for 50 ignition cycles.
POSSIBLE CAUSES
MEMORY SEAT MIRROR MODULE SENSOR GROUND OPEN
SEAT POSITION SENSOR GROUND WIRE OPEN
5 VOLT SUPPLY SHORTED HIGH
CHECK VOLTAGE ON FRONT RISER POSITION SIGNAL CIRCUIT
FRONT RISER SENSOR HIGH
FRONT RISER SENSOR SHORT TO MOTOR
MEMORY SEAT MIRROR MODULE FRONT RISER HIGH
STORED DIAGNOSTIC TROUBLE CODE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Memory Seat Mirror Module.
Operate the driver’s power seat and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRB check for the same DTC to reset in the MSMM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Turn ignition off.
Disconnect the Driver Power Seat Front Riser Position Sensor connector.
Measure the resistance of the Seat Position Sensor Ground circuit at the Driver
Power Seat Front Riser Position Sensor connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 3
No
→ Go To 8
675
MEMORY SEAT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст