Chrysler Town, Dodge Caravan. Manual — part 747
TEST
ACTION
APPLICABILITY
5
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Measure the resistance between ground and the Sensor Return circuit.
Is the resistance below 10 ohms?
All
Yes
→ Go To 6
No
→ Go To 7
6
If there are no possible causes remaining, view repair.
All
Repair
Replace the ATC Remote Sensor.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
7
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Measure the resistance of the Sensor Return circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 8
No
→ Repair the Sensor Return circuit for an open.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
8
If there are no possible causes remaining, view repair.
All
Repair
Replace the ATC.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
9
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Turn the ignition on.
Measure the voltage of the KDB 2 Clock circuit.
Is the voltage above 1.0 volt?
All
Yes
→ Repair the KDB 2 Clock circuit for a short to voltage.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 10
10
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Measure the resistance between ground and the KDB 2 Clock circuit.
Is the resistance above 100k ohms?
All
Yes
→ Go To 11
No
→ Repair the KDB 2 Clock circuit for a short to ground.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
224
AUTOMATIC TEMPERATURE CONTROL
FRONT IR SENSOR NOT CALIBRATED (ACTIVE) —
Continued
TEST
ACTION
APPLICABILITY
11
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Measure the resistance of the KDB 2 Clock circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 12
No
→ Repair the KDB 2 Clock circuit for an open.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
12
If there are no possible causes remaining, view repair.
All
Repair
Replace the ATC.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
13
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Measure the resistance between ground and the KDB 2 Data circuit.
Is the resistance above 100k ohms?
All
Yes
→ Go To 14
No
→ Repair the KDB 2 Data circuit for a short to ground.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
14
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Measure the resistance of the KDB 2 Data circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 15
No
→ Repair the KDB 2 Data circuit for an open.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
15
If there are no possible causes remaining, view repair.
All
Repair
Replace the ATC.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
225
AUTOMATIC TEMPERATURE CONTROL
FRONT IR SENSOR NOT CALIBRATED (ACTIVE) —
Continued
TEST
ACTION
APPLICABILITY
16
Turn the ignition off.
Disconnect the ATC Remote Sensor harness connector.
Disconnect the ATC C3 harness connector.
Measure the resistance of the Protected Ignition circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the ATC.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Protected Ignition circuit for an open.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
226
AUTOMATIC TEMPERATURE CONTROL
FRONT IR SENSOR NOT CALIBRATED (ACTIVE) —
Continued
Symptom:
FRONT KEYBOARD COMMUNICATION FAULT (ACTIVE)
When Monitored and Set Condition:
FRONT KEYBOARD COMMUNICATION FAULT (ACTIVE)
When Monitored:
With the ignition on and the IOD fuse installed.
Set Condition:
This DTC will set if there is an internal fault in the ATC head.
POSSIBLE CAUSES
ATC
TEST
ACTION
APPLICABILITY
1
This DTC indicates a fault in the ATC.
View repair.
All
Repair
Replace the ATC.
With the DRBIII
t, reset the ATC after repair is complete.
Perform BODY VERIFICATION TEST - VER 1.
227
AUTOMATIC TEMPERATURE CONTROL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст