Chrysler Town, Dodge Caravan. Manual — part 437
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Luggage rack crossbar fasteners
4
—
35
Lumbar support handle screw
1
—
9
Pivot bolt to the body half of hood hinge
28
21
—
Prop assembly to lifgate bolts
28
21
—
Rear door glass to regulator bolt
11
8
—
Rear door hinge to B-pillar bolt
28
20
—
Rear door hinge to door bolt
28
20
—
Rear door latch striker
28
20
—
Rear latch to sliding door end frame
28
20
—
Rear seat back to seat cushion bolt
27
19
—
Recliner to seat back frame
12
9
—
Seatback frame upper rail
8
—
71
Seatback hinge bolt
48
35
—
Seatback hinge cover screws
2.3
—
20
Shoulder belt turning loop onto height adjuster
39
29
—
Side view mirror bolts
10
—
85
Sliding door center hinge adjusting bolt
15
—
130
Sliding door glass nuts
3.4
—
30
Sliding door latch striker
28
21
—
Sliding door to roller arm bracket
12
9
—
Storage bin track guide to seat riser
3.5
—
31
Sunroof opening panel to lifter arm screws
5
44
Sunroof opening panel motor screws
4
35
Sunroof trough bracket to roof bolts
6
53
Sunroof trough to trough bracket bolts
6
53
Sunroof trough bracket bolts
6
53
Support cylinders to liftgate
28
21
—
BODY LUBRICATION
LUBRICATION REQUIREMENTS
Body
mechanisms
and
linkages
should
be
inspected, cleaned, and lubricated, as required, to
maintain ease of operation and to provide protection
against rust and wear. When performing other under
hood services, the hood latch release mechanism and
safety catch should be inspected, cleaned, and lubri-
cated. During the winter season, external door lock
cylinders should be lubricated to assure proper oper-
ation when exposed to water and ice.
Prior to the application of any lubricant, the parts
concerned should be wiped clean to remove dust and
grit. If necessary, a suitable solvent can be used to
clean the item to be lubricated. After lubricating a com-
ponent, any excess oil or grease should be removed.
LUBRICANT APPLICATION
DOOR LOCK CYLINDERS
(1) Apply a small amount of lubricant directly into
the lock cylinder.
(2) Apply a small amount of lubricant to the key.
(3) Insert key into lock cylinder and cycle the
mechanism from the locked to the unlocked position.
NOTE: Do not add more lubricant.
(4) Cycle the lock cylinder mechanism several
times to allow the lubricant to flow throughout the
cylinder.
(5) Wipe all lubricant from exterior of lock cylinder
and key.
ALL OTHER BODY MECHANISMS
(1) Clean component as described above.
23 - 12
BODY
RS
BODY (Continued)
(2) Apply specified lubricant to all pivoting and
sliding contact areas of component.
LUBRICANT USAGE
ENGINE OIL
• Door Hinges – Hinge Pin and Pivot Contact
Areas
• Hood Hinges – Pivot Points
• Liftgate Hinges
MOPAR
T
SPRAY WHITE LUBE OR EQUIVALENT
• Door Check Straps
• Liftgate Latches
• Liftgate Prop Pivots
• Ash Receiver
• Fuel Filler Door Remote Control Latch Mecha-
nism
• Parking Brake Mechanism
• Sliding Seat Tracks
• Liftgate Latch
MOPAR
T
Multipurpose GREASE OR EQUIVALENT
• All Other Hood Mechanisms
MOPAR
T
LOCK CYLINDER LUBRICANT OR
EQUIVALENT
• Door Lock Cylinders
• Liftgate Lock Cylinder
SPECIAL TOOLS
BODY
INDEX
DESCRIPTION
FIGURE
STICK, TRIM C 4755
16
REMOVER, MOLDINGS C-4829
17
PLIERS, HEADLINER CLIP 6967
18
Fig. 16 STICK, TRIM C 4755
Fig. 17 REMOVER, MOLDINGS C-4829
Fig. 18 PLIERS, HEADLINER CLIP 6967
RS
BODY
23 - 13
BODY (Continued)
DOOR - FRONT
TABLE OF CONTENTS
page
page
APPLIQUE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . 14
CHECK STRAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 16
DOOR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . 17
FRAME CLOSEOUT MOLDING
REMOVAL – A-PILLAR-HEADER, OR B-PILLAR
INSTALLATION – A-PILLAR-HEADER, OR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 19
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 20
TRIM PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 20
WATERSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 21
WINDOW CRANK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 21
EXTERIOR HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
WINDOW REGULATOR - POWER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
WINDOW REGULATOR - MANUAL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
APPLIQUE
REMOVAL
(1) Roll door glass down.
(2) Remove outer door belt molding.
(3) Disengage clips holding front edge of applique
to door frame.
(4) Remove applique from vehicle (Fig. 1).
INSTALLATION
(1) Position applique on vehicle.
(2) Hook rear edge of applique over rear edge of
door frame and seat applique bottom edge on sheet
metal.
(3) Engage clips to hold front edge of applique to
door frame.
(4) Install outer door belt molding.
23 - 14
DOOR - FRONT
RS
CHECK STRAP
REMOVAL
(1) Remove front door trim panel.
(2) Remove front door watershield (Refer to 23 -
BODY/DOOR - FRONT/WATERSHIELD - REMOV-
AL).
(3) Remove front door speaker, if equipped.
(4) Remove bolts attaching door check strap to
A-pillar.
(5) Remove nuts attaching check strap to door end
frame (Fig. 2).
(6) Remove check strap from door through speaker
hole.
INSTALLATION
(1) Position check strap on door through speaker
hole.
(2) Install nuts to attach check strap to door end
frame. Tighten nuts to 11 N·m (90 in. lbs.) torque.
(3) Install bolts to attach check strap to A-pillar.
Tighten bolts to 12 N·m (105 in. lbs.) torque.
(4) Install door speaker, if equipped.
(5) Install front door trim panel.
DOOR
REMOVAL
(1) Remove front wheelhouse splash shield. (Refer
to
23
-
BODY/EXTERIOR/LF
WHEELHOUSE
SPLASH SHIELD - REMOVAL)
(2) Disengage clips attaching door harness wire
connector to inner fender brace.
(3) Disconnect positive lock slide on the side of the
wire connectors (Fig. 3).
(4) Depress lock tab attaching wire connector
halves together.
(5) Disconnect door harness from body wiring har-
ness.
(6) Remove bolts attaching door check strap to
A-pillar (Fig. 4).
(7) Support door on suitable lifting device.
(8) Remove bolts attaching lower hinge to door end
frame (Fig. 5).
(9) Steady door on lifting device and remove bolts
attaching upper hinge to door end frame.
(10) Remove door from vehicle.
Fig. 1 FRONT DOOR APPLIQUE
1 - GLASS RUN WEATHERSTRIP
2 - CLIPS
3 - APPLIQUE
4 - FRONT DOOR
Fig. 2 FRONT DOOR CHECK STRAP
1 - FRONT DOOR
2 - DOOR CHECK STRAP
RS
DOOR - FRONT
23 - 15
APPLIQUE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст