Chrysler Crossfire. Manual — part 311
BODY VERIFICATION TEST
BODY VERIFICATION TEST
1.
Turn the ignition off.
Disconnect all jumper wires and reconnect all previously disconnected components and connectors.
Note: If the SKREEM or the PCM was replaced, refer to the service information for proper programming
procedures.
If the Body Control Module was replaced, turn the ignition on for 15 seconds (to allow the new BCM to learn VIN)
or engine may not start.
Program all RKE transmitters and other options as necessary.
With the DRB III
T
, erase all Diagnostic Trouble Codes (DTCs) from ALL modules. Start the engine and allow it to
run for 2 minutes. Operate all functions of the system that caused the original complaint.
Ensure that all accessories are turned off and the battery is fully charged.
Turn the ignition off and wait 5 seconds. Turn the ignition on and using the DRB III
T
, read DTCs from ALL modules.
Are any DTCs present or is the original complaint still present?
Are any DTCs present?
YES
>> Repair is not complete, refer to appropriate symptom.
NO
>> Repair is complete.
ZH
POWER SEATS - ELECTRICAL DIAGNOSTICS
8N - 93
SCHEMATICS AND DIAGRAMS
POWER
SEA
TS
CIRCUIT
DIAGRAM
8N - 94
POWER SEATS - ELECTRICAL DIAGNOSTICS
ZH
POWER SEATS - SERVICE INFORMATION
TABLE OF CONTENTS
page
page
POWER SEATS - SERVICE INFORMATION
. . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . . . . . . . . . . . . 95
. . . . . . . . . . . . . . . . 96
. . . . . . . . . . . . . . . . . . . . . . . 96
POWER SEAT SWITCH
. . . . . . . . . . . . . . . . 96
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
. . . . . . . . . . . . . . . . . . . . . . . . . 98
REAR RISER MOTOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
. . . . . . . . . . . . . . . . . . . . . . . . 100
HORIZONTAL AND FRONT RISER MOTORS
INSTALLATION - HORIZONTAL MOTOR
INSTALLATION - FRONT RISER MOTOR
RECLINER MOTOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
. . . . . . . . . . . . . . . . . . . . . . . . 105
POWER SEAT TRACK
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
. . . . . . . . . . . . . . . . . . . . . . . . 107
POWER SEATS - SERVICE INFORMATION
DESCRIPTION
Both seats feature power adjustable positioning and
power reclining as standard equipment. Each seat
contains a lower (1) and a rear (2) power adjustment
switch located on the lower outboard seat trim panel
between the seat base and the door. The driver’s seat
features 8-way adjustment while the passenger’s seat
is 4-way adjustable.
OPERATION
The power seat lower switch adjusts the bottom portion of the seat forward and backward as well as tilting upward
and downward both in the front and rear when the switch is pressed in that direction. The back portion of the seat
reclines when the power seat rear switch is tilted forward or rearward. The driver side power seat switches are
operational with the driver door open, regardless of the ignition switch key position. If the driver door is closed, the
ignition switch key must be turned to the ON/RUN position. See the Owner’s Manual in the glove box for more
information.
ZH
POWER SEATS - SERVICE INFORMATION
8N - 95
DIAGNOSIS AND TESTING
Before any testing of the Power Seat System is performed, the battery should be fully charged. All the wiring har-
ness connectors should be inspected and cleaned, if necessary, to ensure good connections.
1. If all of the power seat functions are inoperative, check Fuse 22 for the driver seat, and Fuse 21 for the pas-
senger seat in the Underhood Accessory Fuse Block.
2. With the dome lamp on, apply the power seat switch in the direction of the failure.
3. If the dome lamp dims, the seat or the power seat track may be jammed. Check under and behind the seat for
binding or obstructions.
4. If the dome lamp does not dim, proceed with testing of the individual power seat system components and cir-
cuits.
For complete power seat system diagnosis, refer to Power Seats Electrical Diagnostics in this section.
SPECIFICATIONS
TORQUE SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Front Riser Motor
Attachment Screw
4
—
35
Horizontal Motor
Attachment Screw
4
—
35
Rear Riser Motor
Attachment Nut
4
—
35
POWER SEAT SWITCH
DIAGNOSIS AND TESTING
For complete power seat system diagnosis, refer to Power Seats Electrical Diagnostics in this section.
REMOVAL
1. Remove the front seat. (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
2. Remove the bolt (1) attaching the side panel to the
seat base.
8N - 96
POWER SEATS - SERVICE INFORMATION
ZH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст