Chrysler Crossfire. Manual — part 845
9610 MAIN CYLINDER TRAVEL SENSOR (ROD SIDE) +/- CIRCUITS OPEN/SHORT
TO GROUND (CONTINUED)
4.
Open Main Cylinder Travel Sensor (Rod Side) (-) Circuit
Turn the ignition off.
Disconnect the Power Top Control Module C1 harness connector.
Measure the resistance of the Main Cylinder Travel Sensor (Rod Side)
(-) circuit from the Power Top Travel Sensors harness connector to the
Power Top Control Module C1 harness connector.
Is the resistance below 5.0 ohms?
Yes
>> Go To 5
No
>> Repair the Main Cylinder Travel Sensor (Rod Side) (-) cir-
cuit for an open.
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
5.
Main Cylinder Travel Sensor (Rod Side) (-) Circuit Shorted to Ground
With the ignition off.
Measure the resistance between ground and the Main Cylinder Travel
Sensor (Rod Side) (-) circuit.
Is resistance below 100 komhs?
Yes
>> Repair the Main Cylinder Travel Sensor (Rod Side) (-) cir-
cuit for a short to ground.
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
No
>> Replace the Power Top Control Module.(Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES/
POWER TOP CONTROL MODULE - REMOVAL)
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
ZH
CONVERTIBLE TOP
23 - 51
9610 MAIN CYLINDER TRAVEL SENSOR (ROD SIDE) +/- CIRCUITS OPEN/SHORT
TO GROUND (CONTINUED)
6.
Open Main Cylinder Travel Sensor (Rod Side) (+) circuit
With the ignition on.
Measure the voltage of the Main Cylinder Travel Sensor (Rod Side) (+)
circuit by backprobing from the Power Top Control Module C1 harness
connector.
Is the voltage above 10.0 volts?
Yes
>> Repair the Main Cylinder Travel Sensor (Rod Side) (+) cir-
cuit for an open.
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
No
>> Go To 7
7.
Main Cylinder Travel Sensor (Rod Side) (+) Circuit Shorted to Ground
Turn the ignition off.
Disconnect the Power Top Control Module C1 harness connector.
Measure the resistance between ground and the Main Cylinder Travel
Sensor (Rod Side) (+) circuit.
Is resistance below 100 komhs?
Yes
>> Repair the Main Cylinder Travel Sensor (Rod Side) (+) cir-
cuit for a short to ground.
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
No
>> Replace the Power Top Control Module.(Refer to 8 -
ELECTRICAL/ELECTRONIC
CONTROL
MODULES/
POWER TOP CONTROL MODULE - REMOVAL)
Perform POWER TOP CONTROL MODULE VERIFICA-
TION TEST.
23 - 52
CONVERTIBLE TOP
ZH
9610 MAIN CYLINDER TRAVEL SENSOR (ROD SIDE) +/- CIRCUITS OPEN/SHORT
TO GROUND (CONTINUED)
8.
INTERMITTENT WIRING AND CONNECTORS
The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for a possible
intermittent condition.
Note: Check connectors — Clean/repair as necessary. Poor pin to terminal connections can set DTCs.
Note: Check for any Technical Service Bulletins that may apply.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors specific to this DTC. Wiggle the
wires while checking for shorts and open circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform CONVERTIBLE TOP CONTROL MODULE VERIFICATION TEST.
No
>> The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for
a possible intermittent condition.
ZH
CONVERTIBLE TOP
23 - 53
9611 MAIN CYLINDER TRAVEL SENSOR (ROD SIDE) (-) CIRCUIT SHORT TO B(+)
23 - 54
CONVERTIBLE TOP
ZH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст