Chrysler Crossfire. Manual — part 872
9904 MAIN CYLINDER TRAVEL SENSOR (BASE SIDE) STUCK
ZH
CONVERTIBLE TOP
23 - 159
9904 MAIN CYLINDER TRAVEL SENSOR (BASE SIDE) STUCK (CONTINUED)
•
When Monitored: Continuous with the ignition on.
•
Set Condition: When the Power Top Control Module senses the Main Travel Sensor (Base Side) active
with the Power Top Switch is depressed for more than 60 seconds.
Possible Causes
POWER TOP CONTROL MODULE
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.
Diagnostic Test
1.
Check for Current DTCs
Turn the ignition on.
With the DRBIII
T
, read and record the Power Top Control Module
(PTCM) DTCs.
Note: If any other Main Cylinder Travel Sensor DTCs have been
set, diagnose the other Power Top Control Module (PTCM) DTCs
first before continuing.
With the DRB III
T
, erase the Power Top Control Module (PTCM)
DTCs.
Press the Power Top Switch to raise and lower the Power Top.
With the DRBIII
T
, read the Power Top Control Module (PTCM) DTCs.
Did this DTC set again?
Yes
>> Replace the Power Top Control Module.(Refer to 8 -
ELECTRICAL/ELECTRONIC CONTROL MODULES/POWER TOP CONTROL MODULE - REMOVAL).
Perform POWER TOP CONTROL MODULE VERIFICATION TEST.
No
>> Go To 2
2.
INTERMITTENT WIRING AND CONNECTORS
The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for a possible
intermittent condition.
Note: Check connectors — Clean/repair as necessary. Poor pin to terminal connections can set DTCs.
Note: Check for any Technical Service Bulletins that may apply.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors specific to this DTC. Wiggle the
wires while checking for shorts and open circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform POWER TOP CONTROL MODULE VERIFICATION TEST.
No
>> The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for
a possible intermittent condition.
23 - 160
CONVERTIBLE TOP
ZH
9905 REAR BOW CYLINDER TRAVEL SENSOR (ROD SIDE) INOPERATIVE
ZH
CONVERTIBLE TOP
23 - 161
9905 REAR BOW CYLINDER TRAVEL SENSOR (ROD SIDE) INOPERATIVE (CONTINUED)
•
When Monitored: Continuous with the ignition on.
•
Set Condition: When the Power Top Control Module senses the Rear Bow Travel Sensor (Rod Side)
inactive with the Power Top in the closed position.
Possible Causes
POWER TOP CONTROL MODULE
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding.
Diagnostic Test
1.
Check for Current DTCs
Turn the ignition on.
With the DRBIII
T
, read and record the Power Top Control Module
(PTCM) DTCs.
Note: If any other Rear Bow Cylinder Travel Sensor DTCs have
been set, diagnose the other Power Top Control Module (PTCM)
DTCs first before continuing.
With the DRB III
T
, erase the Power Top Control Module (PTCM)
DTCs.
Press the Power Top Switch to raise and lower the Power Top.
With the DRBIII
T
, read the Power Top Control Module (PTCM) DTCs.
Did this DTC set again?
Yes
>> Replace the Power Top Control Module.(Refer to 8 -
ELECTRICAL/ELECTRONIC CONTROL MODULES/POWER TOP CONTROL MODULE - REMOVAL).
Perform POWER TOP CONTROL MODULE VERIFICATION TEST.
No
>> Go To 2
2.
INTERMITTENT WIRING AND CONNECTORS
The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for a possible
intermittent condition.
Note: Check connectors — Clean/repair as necessary. Poor pin to terminal connections can set DTCs.
Note: Check for any Technical Service Bulletins that may apply.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors specific to this DTC. Wiggle the
wires while checking for shorts and open circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform POWER TOP CONTROL MODULE VERIFICATION TEST.
No
>> The condition that caused this DTC to set is currently not present. Inspect the related wiring harness for
a possible intermittent condition.
23 - 162
CONVERTIBLE TOP
ZH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст