Chrysler Stratus Convertible. Manual — part 239
(5) Pull instrument panel top cover up enough to
gain access to knee bolster screws (Fig. 18).
(6) Remove lower knee bolster screws and knee
bolster.
(7) Remove screws from lower steering column
shroud (Fig. 19).
(8) Pull lower shroud to clear ignition cylinder and
key release, if equipped (Fig. 20).
(9) Hold tilt wheel lever down and slide lower
shroud forward to remove it from column (Fig. 21).
(10) Tilt wheel to full down position and remove
upper steering column shroud.
(11) Remove screws holding multi-function switch
to lock housing (Fig. 22).
(12) Place key cylinder in RUN position. Depress
lock cylinder retaining tab and remove key cylinder
(Fig. 23).
(13) Disconnect electrical connectors from ignition
switch (Fig. 24) and (Fig. 25).
(14) Remove ignition switch mounting screw (Fig.
24) with a #10 Torx
t tamper proof bit.
(15) Depress retaining tabs (Fig. 14) and pull igni-
tion switch from steering column.
Fig. 13 Crankshaft Position Sensor—2.0L
1 – CRANKSHAFT POSITION SENSOR
2 – OIL FILTER
3 – GENERATOR
Fig. 14 Ignition Switch—Viewed From Below
Column
1 – IGNITION SWITCH
2 – LOCK CYLINDER HOUSING
3 – RETAINING TABS
Fig. 15 Instrument Panel Top Cover—Left End
1 – FUSE PANEL COVER
2 – TOP COVER SCREW
Fig. 16 Center Bezel
1 – CENTER BEZEL
JX
IGNITION SYSTEM
8D - 7
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Ensure the ignition switch is in the RUN posi-
tion and the actuator shaft in the lock housing is in
the RUN position.
(2) Carefully
install
the
ignition
switch.
The
switch will snap over the retaining tabs (Fig. 26).
Install mounting screw (Fig. 24).
(3) Install electrical connectors to ignition switch.
(4) Install upper and lower shrouds.
(5) Install key cylinder (cylinder retaining tab will
depress only in the RUN position).
(6) Connect negative cable to battery.
(7) Check for proper operation of ignition switch
and key-in warning switch.
Fig. 17 Instrument Panel Top Cover—Center
1 – TOP COVER SCREWS
Fig. 18 Knee Bolster Attaching Points
1 – KNEE BOLSTER SCREW LOCATIONS UNDER TOP COVER
2 – LOWER SCREW LOCATIONS
Fig. 19 Lower Steering Column Shroud Screw
Locations
1 – LOWER STEERING COLUMN SHROUD SCREW LOCATIONS
Fig. 20 Remove Lower Shroud From Ignition
Cylinder
1 – LOWER SHROUD
2 – KEY CYLINDER
Fig. 21 Lower Shroud Removal
1 – LOWER SHROUD
2 – TILT LEVER
8D - 8
IGNITION SYSTEM
JX
REMOVAL AND INSTALLATION (Continued)
LOCK KEY CYLINDER
REMOVAL
(1) Disconnect
negative
cable
from
auxillary
jumper terminal.
(2) Remove upper steering column shroud.
(3) Pull lower shroud down far enough to access
lock cylinder retaining tab.
Fig. 22 Multi-Function Switch Removal/Installation
1 – MULTI-FUNCTION SWITCH
2 – ATTACHING SCREWS
Fig. 23 Lock Cylinder Removal
1 – IGNITION SWITCH
2 – SCREWDRIVER
3 – LOCK CYLINDER RETAINING TAB
Fig. 24 Ignition Switch
1 – ATTACHING/GROUNDING SCREW
2 – LOCK HOUSING
3 – IGNITION SWITCH
4 – MULTI-FUNCTION SWITCH
Fig. 25 Ignition Switch Connectors
1 – KEY IN SWITCH
2 – PRNDL SWITCH
3 – IGNITION SWITCH
JX
IGNITION SYSTEM
8D - 9
REMOVAL AND INSTALLATION (Continued)
(4) Place key cylinder in RUN position. Depress
retaining tab and remove key cylinder (Fig. 27).
INSTALLATION
(1) Install key in lock cylinder. Turn key to run
position (retaining tab on lock cylinder can be
depressed).
(2) The shaft at the end of the lock cylinder aligns
with the socket in the end of the housing. To align
the socket with the lock cylinder, ensure the socket is
in the Run position (Fig. 28).
(3) Align the lock cylinder with the grooves in the
housing. Slide the lock cylinder into the housing
until the tab sticks through the opening in the hous-
ing.
(4) Turn the key to the Off position. Remove the
key.
(5) Install steering column shrouds.
(6) Connect negative cable to auxillary battery ter-
minal on shock tower.
IGNITION INTERLOCK
Refer to the Transaxle section for Shifter/Ignition
Interlock Service.
LOCK CYLINDER HOUSING
Refer to Steering Column in Group 19, Steering,
for Lock Cylinder Housing Service.
SPECIFICATIONS
VEHICLE EMISSION CONTROL INFORMATION
LABEL
DESCRIPTION
All models have a Vehicle Emission Control Infor-
mation (VECI) Label. Chrysler permanently attaches
the label in the engine compartment. It cannot be
removed without defacing information and destroying
the label.
The label contains the vehicle’s emission specifica-
tions and vacuum hose routings. All hoses must be
connected and routed according to the label.
Fig. 26 Ignition Switch Installation
1 – LOCK CYLINDER HOUSING
2 – SHAFT
Fig. 27 Lock Cylinder Retaining Tab
1 – LOCK CYLINDER RETAINING TAB
Fig. 28 Socket in Lock Cylinder Housing
1 – LOCK CYLINDER HOUSING
2 – SOCKET
8D - 10
IGNITION SYSTEM
JX
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст