Chrysler Stratus Convertible. Manual — part 121
(2) Route recliner cable in front of metal strap at
bottom of the seat back frame (Fig. 10).
(3) Position seat back to seat frame.
(4) Install wire connector for seat belt retractor to
bracket located under seat cushion.
(5) Install wiring tie strap holding retractor wiring
harness to recliner cable.
(6) Install bolt attaching recliner lead screw to
seat frame. Tighten bolt to 45.3 N·m (33.3 ft. lbs.)
torque.
(7) Install pivot bolts attaching seat back to seat
frame. Tighten bolts to 51.0 N·m (33.3 ft. lbs.) torque.
(8) Attach easy-entry rod to seat back, passenger
side only.
(9) Install easy-entry washer and E-clip, passenger
side only.
(10) Install seat cushion.
(11) Feed recliner cable through hole in seat
adjuster and engage cable eyelet to arm on seat
adjuster.
(12) Install new recliner cable eyelet clip to arm on
seat frame (Fig. 6).
(13) Position seat belt buckle washer to bolt on
side of seat adjuster.
(14) Position seat belt buckle to bolt on side of seat
adjuster and install nut.
(15) Install new nut to hold seat belt buckle to
seat adjuster.
(16) Position lower seat belt anchor to bolt on seat
adjuster.
(17) Verify that seat belt is routed such that it will
not be twisted when engaged to the seat belt buckle.
(18) Install new nut holding lower seat belt anchor
to seat frame (Fig. 6).
NOTE: The tighten the lower seat belt anchor and
seat belt buckle nuts to 45.3 N·m (33.3 ft. lbs.)
torque.
NOTE: Verify that a minimum of three threads
extend beyond the lower seat belt anchor nut and
that the lower seat belt anchor swivels freely. If
both conditions are not found, remove nut, torque
bolt, and while preventing bolt from turning, torque
nut.
(19) Install seat side shield. Verify that side and
rear screws go through the rubber bellows.
(20) Install seat to vehicle. Refer to procedures
found in this section.
Fig. 8 Recliner Lead Screw
1 – RECLINER MECHANISM
2 – LEAD SCREW
3 – SEAT FRAME
Fig. 9 Recliner Lead Screw
1 – LEAD SCREW SPRING PLATE
2 – LEAD SCREW
Fig. 10 Route Recliner Cable
1 – NEW CABLE ROUTING (DRIVER SEAT)
2 – BACK FRAME STRAP
JX
BODY
23 - 17
REMOVAL AND INSTALLATION (Continued)
FRONT SEAT BACK COVER
REMOVAL
(1) Remove seat from vehicle.
(2) Remove head restraint (Fig. 11) by depressing
headrest button and using a pick tool in access hole
simultaneously.
(3) Remove seat back.
(4) Remove upper recliner handle and lumber
adjustment handle, if so equipped.
(5) Remove seat side shield.
(6) Remove nut attaching lower seat belt anchor to
seat frame (Fig. 6).
(7) Remove seat belt bezel.
NOTE: The torque prevailing nut used to secure the
lower seat belt anchor is not reusable. Verify avail-
ability prior to proceeding.
(8) Remove plastic J-strip retainer at bottom of
seat back (Fig. 12).
(9) Remove hog rings holding seat cover seam
cords to wires in seat back foam (Fig. 13) and (Fig.
14).
(10) Poll seat cover upward to mid point position
(Fig. 15).
(11) Feed seat belt bezel and seat belt through
seat cover while pulling cover from seat back foam.
(12) Remove hog rings attaching the seat cover
seam cords and wires to seat back foam.
(13) Remove head restraint guides (Fig. 16).
(14) Remove seat back cover from seat back foam
and frame.
INSTALLATION
(1) Position seat back cover on to seat back foam
and frame.
(2) Install head restraint guides
(3) Install hog rings attaching seat back foam to
seat back frame.
(4) Feed seat belt bezel and seat belt through hole
in seat cover.
(5) Route recliner cable in front of metal strap at
bottom of the seat back frame (Fig. 10).
(6) Pull seat cover downward to first horizontal
trench in seat back foam.
(7) Align seat cover horizontal seam center notch
to center hog ring location.
(8) Install hog rings, center first, to hold seat back
cover seam wire to wire in seat back foam.
Fig. 11 Head Restraint Removal
1 – HEADREST
2 – SEAT
3 – ACCESS HOLE
4 – PICK TOOL
Fig. 12 Seat Cover Retainer Strip
1 – SEAT BACK
2 – PLASTIC RETAINER STRIP
Fig. 13 Hog Rings
1 – SEAT COVER SEAM STRAP
2 – HOG RING
23 - 18
BODY
JX
REMOVAL AND INSTALLATION (Continued)
(9) Install hog rings at hog ring location in vertical
foam trenches to attach the cover seam cords to the
wires in the foam. If vehicle is equipped with cloth
seats, attach the lower ends of horse shoe shaped
wire with the same hog rings.
(10) Install hog rings to hold seat cover seam cords
to wires in seat back foam.
(11) Pull seat cover down fully over seat back
foam.
(12) Install hog rings above bead in seat cover
seam cord to hold cords to hog ring location at bot-
tom of vertical foam trench.
(13) Connect seat cover J- strips at bottom of seat
back.
(14) Slide long snaps on outboard portion of seat
belt bezel inside seat back cover and seat belt retrac-
tor cover.
(15) Install upper recliner handle and lumbar
adjustment handle, if so equipped.
(16) Attach lower seat belt anchor to bolt on seat
adjuster.
(17) Verify that seat belt is routed such that it will
not be twisted when engaged to the seat belt buckle.
(18) Install new nut holding lower seat belt anchor
to seat frame (Fig. 6).
NOTE: The tighten the lower seat belt anchor nut to
45.3 N·m (33.3 ft. lbs.) torque.
(19) Verify that a minimum of three threads
extend beyond the lower seat belt anchor nut and
that the lower seat belt anchor swivels freely. If both
conditions are not found, check that the bolt is fully
engaged to the seat adjuster.
(20) Install seat to vehicle.
(21) Check seat belt operation.
FRONT SEAT CUSHION ASSEMBLY
REMOVAL
(1) Remove seat from vehicle. Refer to procedures
found in this section.
(2) Invert seat on a suitable work surface.
(3) Remove fasteners holding seat cushion assem-
bly to seat adjusters (Fig. 17).
(4) Separate seat cushion assembly from seat
adjusters.
Fig. 14 Lower Seat Hog Rings
1 – SEAT BACK COVER
2 – HOG RING
3 – SEAT BACK CUSHION
Fig. 15 Mid Seat Back Hog Rings
1 – CUSHION COVER
2 – HOG RINGS
3 – CUSHION
Fig. 16 Head Restraint Guides
1 – SEAT CUSHION
2 – ACCESS HOLES
3 – HEADREST GUIDES
4 – BOTTOM OF TOP SEAT FRAME RAIL
JX
BODY
23 - 19
REMOVAL AND INSTALLATION (Continued)
INSTALLATION
(1) Position seat cushion assembly on seat adjust-
ers.
(2) Install fasteners holding seat cushion assembly
to seat adjusters.
(3) Install seat in vehicle. Refer to procedures
found in this section.
FRONT SEAT CUSHION COVER
REMOVAL
(1) Remove seat cushion assembly.
(2) Disengage seat cushion cover retainer channels
from seat cushion frame.
(3) Peel seat cushion cover back from seat cushion
foam to access hog rings holding seat cushion cover
to seat cushion foam.
(4) Remove hog rings holding seat cushion cover to
seat cushion foam.
(5) Separate seat cushion cover from seat cushion
foam.
INSTALLATION
(1) Position seat cushion foam to seat cushion
frame.
(2) Wrap fabric flap on bottom of cushion foam
behind and under rear rail of cushion frame. Pull
fabric tight.
(3) Install hog rings to hold fabric flap to seat
cushion frame.
(4) Position seat cushion cover to seat cushion
foam.
(5) Align horizontal seat cushion cover seam center
notch with center hog ring location in seat cushion
foam.
(6) Install hog rings to hold horizontal seam wire
to wire in seat cushion foam at each hog ring location
provided. Begin at center hog ring location and work
outward.
(7) Install hog rings to hold vertical seam wires to
wires in seat cushion foam at each hog ring location
provided, if seat has vertical seams.
(8) Pull cushion cover down over seat cushion foam
and frame.
(9) Engage seat cushion cover retainer channels to
seat frame.
(10) Install seat cushion assembly.
MANUAL SEAT ADJUSTERS
REMOVAL
(1) Remove seat from vehicle. Refer to appropriate
procedure in this section.
(2) Remove front seat back.
(3) Remove towel bar spring.
(4) Remove push-nuts attaching towel bar to seat
adjusters.
(5) Remove towel bar from seat adjuster.
(6) Remove seat adjusters.
INSTALLATION
(1) Position seat adjusters for reassembly.
(2) Install towel bar to seat adjusters.
(3) Install new push nuts to attach towel bar to
seat adjusters.
(4) Install towel bar spring.
(5) Install front seat back.
(6) Install seat in vehicle. Refer to appropriate pro-
cedure in this section.
POWER SEAT ADJUSTER
REMOVAL
(1) Remove seat from vehicle. Refer to appropriate
procedure in this section.
(2) Remove front seat back.
(3) Remove power seat switch and harness from
seat adjuster.
INSTALLATION
(1) Install power seat switch and harness to seat
adjuster.
(2) Install front seat back.
(3) Install seat in vehicle. Refer to appropriate pro-
cedure in this section.
Fig. 17 Front Seat Cushion
1 – SEAT CUSHION
2 – FASTENERS
3 – SEAT FRAME
4 – FASTENERS
23 - 20
BODY
JX
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст