Chrysler Stratus Convertible. Manual — part 236
DISTRIBUTOR CAP—2.5L
REMOVAL
(1) Remove bolt holding air inlet resonator to
intake manifold.
(2) Loosen clamps holding air cleaner cover to air
cleaner housing.
(3) Remove PCV make-up air hose from air inlet
tube.
(4) Loosen hose clamp at throttle body.
(5) Remove air inlet tube, resonator and air
cleaner cover.
(6) Remove EGR tube.
(7) Remove spark plug cables from distributor cap.
(8) Loosen distributor cap holddown screws and
remove cap (Fig. 14).
(9) Transfer cables from old cap to new cap. The
cap is numbered and so are the cables.
INSTALLATION
(1) Install distributor cap.
(2) Install EGR tube.
(3) Install air inlet tube, resonator and air cleaner
cover.
(4) Tighten hose clamp at throttle body.
(5) Install PCV make-up air hose from air inlet
tube.
(6) Tighten clamps holding air cleaner cover to air
cleaner housing.
(7) Install bolt holding air inlet resonator to intake
manifold.
DISTRIBUTOR ROTOR—2.5L
REMOVAL
(1) Remove bolt holding air inlet resonator to
intake manifold.
(2) Loosen clamps holding air cleaner cover to air
cleaner housing.
(3) Remove PCV make-up air hose from air inlet
tube.
(4) Loosen hose clamp at throttle body.
(5) Remove air inlet tube, resonator and air
cleaner cover.
(6) Remove EGR tube.
(7) Remove spark plug cables from distributor cap.
(8) Loosen distributor cap holddown screws and
remove cap (Fig. 14).
(9) Mark the rotor position and remove rotor. The
mark indicates where to position the rotor when rein-
stalling the distributor.
INSTALLATION
(1) Install rotor on shaft.
(2) Install distributor cap.
(3) Install spark plug cables onto distributor cap.
The cap is numbered as well as the cables. Ensure
sure all high tension wires are firmly in the cap tow-
ers.
(4) Install EGR tube to intake manifold. Tighten
bolts to 11 N·m (95 in. lbs.) torque.
(5) Install air inlet tube, resonator and air cleaner
cover.
(6) Tighten hose clamp at throttle body.
(7) Install PCV make-up air hose to air inlet tube.
(8) Tighten clamps holding air cleaner cover to air
cleaner housing.
(9) Tighten bolt holding air inlet resonator to
intake manifold.
IGNITION SWITCH
The ignition switch attaches to the lock cylinder
housing on the end opposite the lock cylinder (Fig.
16). For ignition switch terminal and circuit identifi-
cation, refer to Group 8W, Wiring Diagrams.
Fig. 16 Ignition Switch—Viewed From Below
Column
1 – IGNITION SWITCH
2 – LOCK CYLINDER HOUSING
3 – RETAINING TABS
JX
IGNITION SYSTEM
8D - 9
REMOVAL AND INSTALLATION (Continued)
REMOVAL
(1) Disconnect
negative
cable
from
auxillary
jumper terminal on driver’s side strut tower.
(2) Remove fuse panel cover from left end of
instrument panel. Remove screw holding end of
instrument panel top cover (Fig. 17).
(3) Pull center bezel off (Fig. 18).
(4) Remove screws holding instrument panel top
cover to center of instrument panel (Fig. 19).
(5) Pull instrument panel top cover up enough to
gain access to knee bolster screws (Fig. 20).
(6) Remove lower knee bolster screws and knee
bolster.
(7) Remove screws from lower steering column
shroud (Fig. 21).
Fig. 17 Instrument Panel Top Cover—Left End
1 – FUSE PANEL COVER
2 – TOP COVER SCREW
Fig. 18 Center Bezel
1 – CENTER BEZEL
Fig. 19 Instrument Panel Top Cover—Center
1 – TOP COVER SCREWS
Fig. 20 Knee Bolster Attaching Points
1 – KNEE BOLSTER SCREW LOCATIONS UNDER TOP COVER
2 – LOWER SCREW LOCATIONS
Fig. 21 Lower Steering Column Shroud Screw
Locations
1 – LOWER STEERING COLUMN SHROUD SCREW LOCATIONS
8D - 10
IGNITION SYSTEM
JX
REMOVAL AND INSTALLATION (Continued)
(8) Pull lower shroud to clear ignition cylinder and
key release, if equipped (Fig. 22).
(9) Hold tilt wheel lever down and slide lower
shroud forward to remove it from column (Fig. 23).
(10) Tilt wheel to full down position and remove
upper steering column shroud.
(11) Remove screws holding multi-function switch
to lock housing (Fig. 24).
(12) Place key cylinder in RUN position. Depress
lock cylinder retaining tab and remove key cylinder
(Fig. 25).
(13) Disconnect electrical connectors from ignition
switch (Fig. 26) and (Fig. 27).
(14) Remove ignition switch mounting screw (Fig.
26) with a #10 Torx
t tamper proof bit.
(15) Depress retaining tabs (Fig. 16) and pull igni-
tion switch from steering column.
INSTALLATION
(1) Ensure the ignition switch is in the RUN posi-
tion and the actuator shaft in the lock housing is in
the RUN position.
Fig. 22 Remove Lower Shroud From Ignition
Cylinder
1 – LOWER SHROUD
2 – KEY CYLINDER
Fig. 23 Lower Shroud Removal
1 – LOWER SHROUD
2 – TILT LEVER
Fig. 24 Multi-Function Switch Removal/Installation
1 – MULTI-FUNCTION SWITCH
2 – ATTACHING SCREWS
Fig. 25 Lock Cylinder Removal
1 – IGNITION SWITCH
2 – SCREWDRIVER
3 – LOCK CYLINDER RETAINING TAB
JX
IGNITION SYSTEM
8D - 11
REMOVAL AND INSTALLATION (Continued)
(2) Carefully
install
the
ignition
switch.
The
switch will snap over the retaining tabs (Fig. 28).
Install mounting screw (Fig. 26).
(3) Install electrical connectors to ignition switch.
(4) Install upper and lower shrouds.
(5) Install key cylinder (cylinder retaining tab will
depress only in the RUN position).
(6) Connect negative cable to battery.
(7) Check for proper operation of ignition switch
and key-in warning switch.
LOCK KEY CYLINDER
REMOVAL
(1) Disconnect
negative
cable
from
auxillary
jumper terminal.
(2) Remove upper steering column shroud.
(3) Pull lower shroud down far enough to access
lock cylinder retaining tab.
(4) Place key cylinder in RUN position. Depress
retaining tab and remove key cylinder (Fig. 29).
INSTALLATION
(1) Install key in lock cylinder. Turn key to run
position (retaining tab on lock cylinder can be
depressed).
(2) The shaft at the end of the lock cylinder aligns
with the socket in the end of the housing. To align
the socket with the lock cylinder, ensure the socket is
in the Run position (Fig. 30).
(3) Align the lock cylinder with the grooves in the
housing. Slide the lock cylinder into the housing
until the tab sticks through the opening in the hous-
ing.
Fig. 26 Ignition Switch
1 – ATTACHING/GROUNDING SCREW
2 – LOCK HOUSING
3 – IGNITION SWITCH
4 – MULTI-FUNCTION SWITCH
Fig. 27 Ignition Switch Connectors
1 – KEY IN SWITCH
2 – PRNDL SWITCH
3 – IGNITION SWITCH
Fig. 28 Ignition Switch Installation
1 – LOCK CYLINDER HOUSING
2 – SHAFT
8D - 12
IGNITION SYSTEM
JX
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст