Chrysler Stratus Convertible. Manual — part 265
Fig. 2 Fog Lamp Alignment-Typical
1 – HIGH INTENSITY AREA
2 – CENTER OF VEHICLE
3 – VERTICAL CENTER OF FOG LAMP
4 – HORIZONTAL CENTER OF FOG LAMP
5 – 200mm (8 in.)
6 – FRONT OF FOG LAMP
7 – 10 METERS (32.8 ft.)
JX
LAMPS
8L - 5
ADJUSTMENTS (Continued)
LAMP BULB SERVICE
TABLE OF CONTENTS
page
page
REMOVAL AND INSTALLATION
HEADLAMP BULB . . . . . . . . . . . . . . . . . . . . . . . . . 6
TURN SIGNAL LAMP BULB . . . . . . . . . . . . . . . . . . 7
FRONT POSITION LAMP BULB . . . . . . . . . . . . . . . 8
SIDE TURN SIGNAL REPEATER LAMP BULB . . . . 9
Rear Fog, Tail, Stop, Turn and Backup Lamp
Bulbs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
LICENSE PLATE LAMP BULB. . . . . . . . . . . . . . . . 11
REMOVAL AND INSTALLATION
HEADLAMP BULB
REMOVAL
(1) Release hood latch and open hood.
(2) Remove headlamp module retaining screws
(Fig. 1).
NOTE: Place a towel between front fascia and
headlamp assembly to prevent vehicle paint dam-
age.
(3) Pull headlamp module away from the radiator
closure panel.
(4) Disconnect necessary electrical from back of
headlamp module.
(5) Pull back protective rubber boot seal (Fig. 2).
(6) Loosen headlamp bulb retaining ring screw
from headlamp module (Fig. 3).
(7) Remove the headlamp bulb from headlamp
module (Fig. 3).
INSTALLATION
CAUTION: Do not touch the glass of halogen bulbs
with fingers or other possibly oily surface, reduced
bulb life will result.
Fig. 1 Headlamp Module Retaining Screws
1 – MODULE SCREWS
2 – HEADLAMP MODULE
Fig. 2 Headlamp Module Orientation
1 – HEADLAMP LEVELING MOTOR
2 – HEADLAMP
3 – PROTECTIVE RUBBER BOOT
4 – FRONT POSITION LAMP
5 – HEADLAMP MODULE
8L - 6
LAMPS
JX
(1) Install headlamp bulb in module, position
retaining ring and tighten retaining screw until bulb
secure.
(2) Install rubber boot in its original position (Fig.
4).
(3) Connect electrical on back of headlamp module.
(4) Verify lamp operation.
(5) Position the headlamp module and install
retaining screws. Torque screws to 1 N·m (10in lbs.).
TURN SIGNAL LAMP BULB
REMOVAL
(1) Release hood latch and open hood.
(2) Remove the headlamp module retaining screws
(Fig. 5).
CAUTION: Place a clean shop towel between the
headlamp module and front fascia to prevent vehi-
cle paint damage.
(3) Pull the headlamp module away from the radi-
ator closure panel far enough to access the turn sig-
nal lamp bulb (Fig. 6).
(4) Rotate the turn signal lamp socket counter
clockwise one quarter turn and pull straight from the
module (Fig. 6).
(5) Rotate and pull bulb from socket.
INSTALLATION
(1) Install bulb in its socket.
(2) Verify lamp operation.
(3) Position headlamp module and install retaining
screws. Torque retaining screws to 1 N·m (10in. lbs.).
Fig. 3 Headlamp Bulb
1 – HEADLAMP BULB
2 – HEADLAMP MODULE
Fig. 4 Headlamp Module Orientation
1 – HEADLAMP LEVELING MOTOR
2 – HEADLAMP
3 – PROTECTIVE RUBBER BOOT
4 – FRONT POSITION LAMP
5 – HEADLAMP MODULE
Fig. 5 Headlamp Module Retaining Screws
1 – MODULE SCREWS
2 – HEADLAMP MODULE
JX
LAMPS
8L - 7
REMOVAL AND INSTALLATION (Continued)
FRONT POSITION LAMP BULB
REMOVAL
(1) Release hood latch and open hood.
(2) Remove headlamp module retaining screws
(Fig. 8).
NOTE: Place a towel between front fascia and
headlamp assembly to prevent vehicle paint dam-
age.
(3) Pull headlamp module away from the radiator
closure panel.
(4) Pull back protective rubber boot seal (Fig. 9).
(5) Remove front position lamp socket from head-
lamp module by pulling straight out (Fig. 9).
(6) Remove front position lamp bulb by rotating
counter-clockwise.
INSTALLATION
(1) Install bulb in socket.
(2) Verify lamp operation.
(3) Install front position lamp and socket in head-
lamp module (Fig. 10).
(4) Install protective rubber boot seal in its origi-
nal position (Fig. 10).
(5) Position the headlamp module and install
retaining screws (Fig. 11). Torque screws to 1 N·m
(10in lbs.).
Fig. 6 Turn Signal Lamp Bulb
1 – TURN SIGNAL LAMP
2 – HEADLAMP MODULE
3 – SOCKET
4 – BULB
Fig. 7 Front Position Lamp Location
1 – PARK, TURN SIGNAL LAMP BULB
2 – HEADLAMP BULB
3 – FRONT POSITION LAMP BULB
Fig. 8 Headlamp Module Retaining Screws
1 – MODULE SCREWS
2 – HEADLAMP MODULE
8L - 8
LAMPS
JX
REMOVAL AND INSTALLATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст