Chrysler 300M, Dodge Interpid. Manual — part 83
LAMPS
TABLE OF CONTENTS
page
page
LAMPS/LIGHTING - EXTERIOR . . . . . . . . . . . . . . . 1
LAMPS/LIGHTING - INTERIOR . . . . . . . . . . . . . . . 47
LAMPS/LIGHTING - EXTERIOR
TABLE OF CONTENTS
page
page
LAMPS/LIGHTING - EXTERIOR
. . . . . . . . . . . . . . . . . 3
DESCRIPTION - TURN SIGNAL & HAZARD
WARNING SYSTEM . . . . . . . . . . . . . . . . . . . . . 3
OPERATION - TURN SIGNAL & HAZARD
. . . . . . . . . . . . . . . . . . . . . 3
DIAGNOSIS AND TESTING - TURN SIGNAL &
. . . . . . . . . . . . . . . . . . . . . 4
BACK UP LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
BACK UP LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
BRAKE LAMP SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIAGNOSIS AND TESTING - BRAKE LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENT - BRAKE LAMP SWITCH
CENTER HIGH MOUNTED STOP LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . 8
CENTER HIGH MOUNTED STOP LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . . . . 9
COMBINATION FLASHER
. . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
DIAGNOSIS AND TESTING - COMBINATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . 10
DAYTIME RUNNING LAMP MODULE
. . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DIAGNOSIS AND TESTING - DAYTIME
. . . . . . . . . . . . . . . 10
DECKLID/TRUNK LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . 10
FOG LAMP
DIAGNOSIS AND TESTING - FOG LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
. . . . . . . . . . . . . . . . . . . . . . . . . 13
FOG LAMP UNIT
STANDARD PROCEDURE - FOG LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
. . . . . . . . . . . . . . . . . . . . . . . . . 14
FRONT POSITION LAMP - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
HEADLAMP
. . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DIAGNOSIS AND TESTING - HEADLAMP
INTENSITY DISCHARGE HEADLAMPS -
300M SPECIAL . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
. . . . . . . . . . . . . . . . . . . . . . . . . 22
HEADLAMP DELAY
. . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
LH
LAMPS
8L - 1
HEADLAMP LEVELING MOTOR - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DIAGNOSIS AND TESTING - HEADLAMP
LEVELING MOTOR - EXPORT . . . . . . . . . . . . 24
DIAGNOSIS AND TESTING - HEADLAMP
LEVELING SYSTEM - EXPORT . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . 25
HEADLAMP LEVELING SWITCH - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
DIAGNOSIS AND TESTING - HEADLAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
HEADLAMP SWITCH
. . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . 26
DIAGNOSIS AND TESTING - HEADLAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
HEADLAMP UNIT
UNIT ALIGNMENT . . . . . . . . . . . . . . . . . . . . . 27
UNIT ALIGNMENT - EXPORT . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 31
LICENSE PLATE LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 31
LICENSE PLATE LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 32
MARKER LAMP - CONCORDE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 32
MARKER LAMP UNIT - CONCORDE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 32
MULTI-FUNCTION SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DIAGNOSIS AND TESTING - MULTI-
. . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . 35
PARK/TURN SIGNAL LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . . . . . 36
REAR FOG LAMP - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DIAGNOSIS AND TESTING - REAR FOG
. . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . 37
REAR FOG LAMP SWITCH - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . 38
SIDE REPEATER LAMP - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DIAGNOSIS AND TESTING - SIDE REPEATER
. . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . 39
SIDE REPEATER LAMP UNIT - EXPORT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
SPOT LAMP - POLICE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
SPOT LAMP ASSEMBLY - POLICE
. . . . . . . . . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . 40
DIAGNOSIS AND TESTING - SPOT LAMP
. . . . . . . . . . . . . . . . . . 40
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
. . . . . . . . . . . . . . . . . . . . . . . . . 42
TAIL LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . 43
TAIL LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . 44
TURN SIGNAL LAMP UNIT - CONCORDE/300M
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . 44
UNDERHOOD LAMP - POLICE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
. . . . . . . . . . . . . . . . . . . . . . . . . 45
UNDERHOOD LAMP UNIT - POLICE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
. . . . . . . . . . . . . . . . . . . . . . . . . 46
8L - 2
LAMPS/LIGHTING - EXTERIOR
LH
LAMPS/LIGHTING - EXTERIOR
DESCRIPTION
DESCRIPTION - POLICE
There are three pair of twisted 18-gauge wires
from the interior-to-front bumper beam area to be
used for the auxiliary flashers, siren, speaker, or con-
trol circuit usage. The twisted pairs are taped back
to the wire harness right by the wire feed to the
ambient temperature sensor behind the front fascia,
in front of the condenser, just to the passenger side of
the vehicle centerline. All police vehicle wiring (addi-
tional circuits added) is taped back to the wire har-
ness with green tape for identification. Refer to
Wiring Diagrams for location and circuit description.
The police package includes a Wig Wag (alternat-
ing flashing of the vehicle high beam headlamps)
connector underneath the instrument panel. This
connector is hard wired to the front high beam head-
lamps and is intended for use with an aftermarket
lighting control module. Refer to Wiring Diagrams for
location and circuit description.
DESCRIPTION - TURN SIGNAL & HAZARD
WARNING SYSTEM
The turn signal and hazard warning system
includes the following major components:
• Combination Flasher
• Hazard Warning Switch
• Turn Signal Cancel Cam
• Turn Signal Indicators
• Turn Signal Lamps
• Turn Signal Switch
SUPPLEMENTAL INDICATORS - 300M SPECIAL
The 300M Special has an added feature to the turn
signal system. Mounted on the outside of the left and
right power outside mirrors are supplemental indica-
tors. These are intended for additional indication to
alert other drivers to see when the vehicle is turning
or changing lanes.
These supplemental indicators are an integral part
of the outside power mirror assembly and cannot be
serviced separately. If found to be faulty or defective,
the entire power outside mirror must be replaced.
These indicators are LED’s and contain resistors
internally to maintain proper operating voltage. The
secondary indicators are spliced directly into the turn
signal circuit.
OPERATION - TURN SIGNAL & HAZARD
WARNING SYSTEM
The turn signal system operates on battery voltage
received on a fused ignition switch output (RUN-
ACC) circuit so that the turn signals will only oper-
ate
with
the
ignition
switch
in
the
ON
or
ACCESSORY positions. The hazard warning system
operates on non-switched battery voltage received on
a fused B(+) circuit so that the hazard warning
remains operational regardless of the ignition switch
position. When the turn signal system is activated,
the turn signal switch and the combination flasher
will cause the selected turn signal indicator, front
park/turn signal lamp, and rear tail/stop/turn signal
lamp to flash ON and OFF. When the hazard warn-
ing system is activated, the hazard warning switch
and the combination flasher will cause both the right
side and the left side turn signal indicators, front
park/turn signal lamps, and rear tail/stop/turn signal
lamps to flash ON and OFF.
SUPPLEMENTAL INDICATORS - 300M SPECIAL
When the multi-function switch requests a left or
right turn, the voltage is sent to the front and rear
turn signals as well as the corresponding supplemen-
tal indicator. For diagnosis of the supplemental indi-
cators,
(Refer
to
8
-
ELECTRICAL/POWER
MIRRORS - DIAGNOSIS AND TESTING).
DIAGNOSIS AND TESTING - TURN SIGNAL &
HAZARD WARNING SYSTEM
When diagnosing the turn signal and hazard warn-
ing circuits, remember that high generator output
can burn out bulbs rapidly and repeatedly. If this is a
problem on the vehicle being diagnosed, be certain to
diagnose and repair the charging system as required.
If the problem being diagnosed is related to a failure
of the turn signals to automatically cancel following
completion of a turn, inspect the multi-function
switch for a faulty or damaged cancel actuator and
inspect the turn signal cancel cam on the clock
spring for damaged lobes or improper installation.
(1) Turn the ignition switch to the ON position.
Actuate the turn signal switch or the hazard warning
switch. Observe the turn signal indicator(s) in the
instrument cluster. If the flash rate is very high,
check for a turn signal bulb that is not lit or is very
dimly lit. Repair the circuits to that lamp or replace
the faulty bulb, as required. If the turn signal indi-
cator(s) fail to light, go to Step 2.
(2) Turn the ignition switch to the OFF position.
Check the fused ignition switch output (RUN-ACC)
fuse in the Junction Block (JB) and the fused B(+)
fuse in the Power Distribution Center (PDC). If OK,
go to Step 3. If not OK, repair the shorted circuit or
component as required and replace the faulty fuse(s).
LH
LAMPS/LIGHTING - EXTERIOR
8L - 3
(3) Check for battery voltage at the fused B(+) fuse
in the PDC. If OK, go to Step 4. If not OK, repair the
open B(+) circuit between the PDC and the battery
as required.
(4) Turn the ignition switch to the ON position.
Check for battery voltage at the fused ignition switch
output (RUN-ACC) fuse in the JB. If OK, go to Step
5. If not OK, repair the open fused ignition switch
output (RUN-ACC) circuit between the JB and the
ignition switch as required.
(5) Turn the ignition switch to the OFF position.
Disconnect and isolate the battery negative cable.
Remove the combination flasher from the rear of the
multi-function switch and replace it with a known
good unit. Reconnect the battery negative cable. Test
the operation of the turn signal and hazard warning
systems. If OK, discard the faulty combination
flasher. If not OK, remove the test flasher and go to
Step 6.
(6) Turn the ignition switch to the ON position.
Check for battery voltage at the fused ignition switch
output (RUN-ACC) circuit in the rear of the multi-
function switch for the combination flasher. If OK, go
to Step 7. If not OK, repair the open fused ignition
switch output (RUN-ACC) circuit between the combi-
nation flasher and the fused ignition switch output
(RUN-ACC) fuse in the JB as required.
(7) Turn the ignition switch to the OFF position.
Check for battery voltage at the fused B(+) circuit
cavity of the instrument panel wire harness connec-
tor for the combination flasher. If OK, go to Step 8. If
not OK, repair the open fused B(+) circuit between
the combination flasher and the fused B(+) fuse in
the PDC as required.
(8) Disconnect the instrument panel wire harness
connector for the multi-function switch. Check for
continuity between the hazard flasher signal circuit
in the instrument panel wire harness connector and
the instrument panel wire harness connector for the
multi-function switch. There should be continuity. If
OK, go to Step 9. If not OK, repair the open hazard
flasher
signal
circuit
between
the
combination
flasher and the multi-function switch as required.
(9) Check for continuity between the right turn
switch sense circuit in the instrument panel wire
harness connector and the instrument panel wire
harness connector for the multi-function switch.
Repeat this check between the left turn switch sense
circuit cavities. If OK, go to Step 10. If not OK,
repair the open right and/or left turn switch sense
circuit(s) between the combination flasher and the
multi-function switch as required.
(10) Check for continuity between the right and/or
left turn signal circuit in the instrument panel wire
harness connector for the combination flasher and
the individual turn signal lamps. There should be
continuity. If OK, test the multi-function switch
(Refer to 8 - ELECTRICAL/LAMPS/LIGHTING -
EXTERIOR/MULTI-FUNCTION SWITCH - DIAG-
NOSIS AND TESTING). If not OK, repair the open
right and/or left turn signal circuit(s) between the
combination flasher and the turn signal lamp(s) as
required.
SPECIFICATIONS
EXTERIOR LAMPS
CAUTION: Do not use bulbs other than those listed
in the Bulb Application Table. Damage to lamp can
result.
Do not touch halogen bulbs with fingers or other
oily surfaces. Bulb life will be reduced.
BULB APPLICATION TABLE
LAMP
MODEL
BULB
Back up
Concorde/
Limited
921
Intrepid/300M
3157K
CHMSL
Concorde/
Limited/300M
921
Intrepid
912
300M
921
Front Parking/Turn
Signal
Limited
3157 AK or
NA
Front Parking/Turn
Signal/Side Marker
Concorde/
300M
3157 K
Intrepid
3157 KNA or
AK
Front Side Marker
Limited
168
Fog lamps
Intrepid
H-3 (35 watt)
300M
H-3 (55 watt)
Limited
9040 (40
Watt)
Headlamps
High Beam
(All)
9005 XSLL
Low Beam (All)
9006 XS
License Plate
All
168
Spot Lamp
Intrepid -
Police
H3 (100 watt)
Tail
300M
3157K
Tail Side Marker
Intrepid
168
8L - 4
LAMPS/LIGHTING - EXTERIOR
LH
LAMPS/LIGHTING - EXTERIOR (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст