Chrysler 300M, Dodge Interpid. Manual — part 351
WINDOW REGULATOR
REMOVAL
(1) Remove flag cover, door trim panel, water
shield as necessary, and pull cup support bracket.
(Refer to 23 - BODY/DOORS - REAR/TRIM PANEL -
REMOVAL)
(2) Slide glass from regulator roller channel (Fig.
12).
(3) Disconnect power window motor wire connec-
tor.
(4) Loosen screw attaching regulator scissor chan-
nel to door panel.
(5) Remove screw and bolt heads from keyhole
slots in door panel.
(6) Loosen bolt attaching regulator support brace
to door panel.
(7) Loosen bolts attaching regulator to door panel.
(8) Remove regulator from door panel.
(9) Slide regulator rearward and rotate forward
end of roller channel through access hole in door
panel.
INSTALLATION
(1) Insert roller channel through access hole in
door panel.
(2) Insert bolt and screw heads through key hole
slots in door panel.
(3) Tighten bolts attaching regulator to door panel.
(4) Tighten bolt to attach regulator support brace
to door panel.
(5) Tighten screw to attach regulator scissor chan-
nel to door panel.
(6) Connect power window motor wire connector.
(7) Lower door glass on to regulator roller channel.
(8) Align glass and verify operation.
(9) Install pull cup support bracket, water shield,
door trim panel and flag cover.
CABLE - REMOTE LOCK
ACTUATOR
REMOVAL
(1) Open the front door.
(2) Loosen the actuator knob lock nut.
(3) Remove the lock actuator knob and lock nut.
(4) Remove the cable housing nut.
(5) Remove the trim panel and watershield. (Refer
to 23 - BODY/DOORS - REAR/TRIM PANEL -
REMOVAL)
(6) Remove the support bracket screws.
(7) Release the clip at the latch and disconnect the
cable.
(8) Remove support tie straps, if equipped.
INSTALLATION
(1) Install the cable into the door and through the
hole in the door shut face.
(2) Install and tighten the cable nut.
(3) Install the knob lock nut and the actuator
knob.
(4) Tighten the lock nut.
(5) Attach the cable to the latch and engage the
clip.
(6) Install the support bracket screws and verify
correct actuator operation.
(7) Loosen the support bracket screws and adjust
the cable if necessary.
(8) Replace any support tie straps, if equipped.
(9) Install the watershield and the trim panel.
(Refer to 23 - BODY/DOORS - REAR/TRIM PANEL -
INSTALLATION)
Fig. 12 REAR DOOR WINDOW REGULATOR
1 - GLASS
2 - LIFT PLATES
3 - GLASS ROLLER CHANNEL
4 - WINDOW REGULATOR
5 - REAR DOOR
LH
DOORS - REAR
23 - 33
EXTERIOR
TABLE OF CONTENTS
page
page
BODY SIDE MOLDINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . 34
COWL GRILLE AND SCREEN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . 35
EXTERIOR NAME PLATES
. . . . . . . . . . . . . . . . 35
INSTALLATION - DOUBLE SIDED TAPE
FRONT STRUT TOWER TO TOWER BRACE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . . . . . 36
GRILLE
. . . . . . . . . . . . . . . . 36
GRILLE OPENING REINFORCEMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . . . . . 37
FRONT FENDER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . 37
WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . 38
REAR WHEELHOUSE SPLASH SHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . 38
SIDE VIEW MIRROR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
SIDE VIEW MIRROR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . 39
BODY SIDE MOLDINGS
REMOVAL
(1) Warm the effected stick on molding and body
metal to approximately 38° C (100° F) using a suit-
able heat lamp or heat gun.
(2) Pull stick on molding from painted surface.
(3) Remove adhesive tape residue from painted
surface of vehicle.
INSTALLATION
(1) If molding is to be reused, remove tape residue
from molding. Clean back of molding with Mopar
t
Super Kleen solvent or equivalent. Wipe molding dry
with lint free cloth. Apply new body side molding
(two sided adhesive) tape to back of molding.
(2) Clean body surface with Mopar
t Super Kleen sol-
vent or equivalent. Wipe surface dry with lint free cloth.
(3) Apply a length of masking tape on the body,
parallel to the top edge of the molding to use as a
guide, if necessary. (Fig. 1)
(4) Remove protective cover from tape on back of
molding. Apply molding to body below the masking
tape guide.
(5) Remove masking tape guide and heat body and
molding, see step one. Firmly press molding to body
surface to assure adhesion.
Fig. 1 BODY SIDE MOLDING
1 - PROTECTIVE COVER
2 - MASKING TAPE GUIDE
3 - MOLDINGS
23 - 34
EXTERIOR
LH
COWL GRILLE AND SCREEN
REMOVAL
(1) Release hood latch and open hood.
(2) Remove wiper arms. (Refer to 8 - ELECTRI-
CAL/WIPERS/WASHERS/WIPER
ARMS
-
REMOVAL)
(3) Remove screws attaching cowl screen at the
windshield and under hood (Fig. 2).
(4) Remove cowl screen from vehicle.
INSTALLATION
(1) Place cowl screen in position on vehicle.
(2) Install cowl screen screws, starting at fender
moving inboard.
(3) Install wiper arms. (Refer to 8 - ELECTRICAL/
WIPERS/WASHERS/WIPER
ARMS
-
INSTALLA-
TION)
EXTERIOR NAME PLATES
REMOVAL
REMOVAL - DOUBLE SIDED TAPE
(1) Mark reference points before removing.
(2) Using a heat gun gently apply heat in a circu-
lar motion to loosen the adhesive bond.
(3) Using a nonmetallic prying device, such as a
plastic or wood trim stick gently pry up at corners
and remove.
(4) Clean off all traces of adhesive or double sided
tape from the panel with a general purpose adhesive
remover.
REMOVAL - ADHESIVES
(1) Mark reference points before removing.
(2) Using a heat gun gently apply heat in a circu-
lar motion to loosen the adhesive bond.
(3) With your fingernail lift up and peel away
badgeing/tape from panel, using a heat gun as you
go.
(4) Clean off all traces of adhesive from the pan-
el(s) with a general purpose adhesive remover.
INSTALLATION
INSTALLATION - DOUBLE SIDED TAPE
(1) Clean panel surface with isopropy alcohol.
(2) Align badgeing to reference points.
(3) Install and press securely to full adhesive con-
tact
(4) Clean away any reference points.
INSTALLATION - ADHESIVES
(1) Clean panel surface with isopropy alcohol.
(2) Remove paper carrier and align badgeing/tape
to reference points or adjacent panel.
(3) Install and press securely, using a plastic
spreader to eliminate all air bubbles.
(4) Remove top protective carrier.
(5) Clean away any reference points.
Fig. 2 COWL SCREEN
1 - PLENUM COWL SCREEN
2 - COWL SCREEN RIGHT
3 - COWL SCREEN LEFT
LH
EXTERIOR
23 - 35
FRONT STRUT TOWER TO
TOWER BRACE
REMOVAL
(1) Open hood.
(2) Remove the cowl screen.
(3) Mark bolt locations on front strut tower to
tower brace.
(4) Remove attaching bolts from the brace (Fig. 3).
(5) Remove front strut tower to tower brace from
vehicle.
(6) For replacement remove weatherstrip.
INSTALLATION
(1) Place in position the front strut tower to tower
brace.
(2) Install front strut tower to tower brace attach-
ing bolts. Check bolt alignment marks.
(3) Tighten the bolts to 38 N·m (28 ft. lbs.) torque.
(4) Install cowl screen.
GRILLE
REMOVAL
REMOVAL - CONCORDE
(1) Open hood.
(2) Remove fascia.
(3) Remove two screws attaching foam.
(4) Remove ten attaching grille clips.
(5) Remove grille.
REMOVAL - 300 M - UPPER
(1) Open hood.
(2) Remove fascia.
(3) Drill out rivets attaching cross bracket to
grille.
(4) Remove upper grille six attaching clips.
(5) Remove grille.
REMOVAL - 300 M - LOWER
(1) Open hood.
(2) Remove fascia.
(3) Remove two screws attaching foam.
(4) Remove lower grille eight attaching clips.
(5) Remove grille.
INSTALLATION
INSTALLATION - CONCORDE
(1) Place grille into position on vehicle.
(2) Install ten attaching grille clips.
(3) Install two screws attaching foam.
(4) Install fascia.
(5) Close hood and check alignment of the grille.
INSTALLATION - 300 M - UPPER
(1) Place grille into position on vehicle.
(2) Install six attaching grille clips.
(3) Install rivets attaching cross bracket to grille.
(4) Install two screws attaching foam.
(5) Install fascia.
(6) Close hood and check alignment of the grille.
INSTALLATION - 300 M - LOWER
(1) Place grille into position on vehicle.
(2) Install eight attaching grille clips.
(3) Install two screws attaching foam.
(4) Install fascia.
(5) Check alignment of the grille.
GRILLE OPENING
REINFORCEMENT
REMOVAL
(1) Open hood.
(2) Mark bolt locations on the upper radiator clo-
sure panel.
(3) Remove bolts attaching windshield washer bot-
tle and speed control servo, if equipped (Fig. 4).
(4) Remove headlamp jackscrews both sides.
(5) Remove fasteners attaching upper bumper fas-
cia.
(6) Remove bolts attaching the forward edge of
upper radiator closure panel.
(7) Remove bolts attaching upper radiator closure
panel.
(8) Disconnect hood latch cable from hood latch.
(9) Remove upper radiator closure panel from vehi-
cle.
(10) For replacement of upper radiator closure
panel, remove hood latch, and any other hardware.
Fig. 3 COWL SUPPORT
1 - COWL SUPPORT
2 - WINDSHIELD
3 - SUPPORT FASTENERS
23 - 36
EXTERIOR
LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст