Chrysler 300M, Dodge Interpid. Manual — part 370

INSTALLATION

(1) Install the sunshade from outside of the vehicle

with the sunroof 90% open.

(2) Put rear guide blocks into sunshade guide

track.

(3) Push sunshade back and down through the

sunroof opening.

(4) Using a flat blade tool, put front guide blocks

into the sunshade track. By pushing the block
towards the center of the vehicle.

(5) Push sunshade back to the glass panel.
(6) Push sunshade down until the sunshade clears

the glass then move sunshade rearward behind the
glass panel.

WIND DEFLECTOR

REMOVAL

(1) Open sunroof glass panel.
(2) Push down one corner of the wind deflector and

let the other corner rise up (Fig. 10).

(3) Push the low corner towards the opposite side

of the vehicle until tab on sunshade clears the body.
Then raise the corner up.

(4) Repeat the procedure to the other corner.
(5) Lift wind deflector to 90% of the way.
(6) Push the attaching ends of the deflector to the

rear of the vehicle to disengage the deflector.

INSTALLATION

(1) Place wind deflector at 90% in the vertical posi-

tion to the sunroof. With the sunroof open.

(2) Push ends of the deflector towards the front of

the vehicle to engage ends.

(3) Lower wind deflector to normal position.
(4) Push one corner to the opposite side of the

vehicle until tab clears vehicle body and lower deflec-
tor for that corner.

(5) Push the side that was just installed com-

pletely down.

(6) Push the opposite corner cross vehicle until tab

clears the body. Then lower deflector to position.

(7) Test sunroof operation.

Fig. 9 SUNSHADE GUIDE BLOCK

1 - GUIDE BLOCK
2 - GUIDE BLOCK SPRING

Fig. 10 WIND DEFLECTOR

1 - WIND DEFLECTOR
2 - TAB

LH

SUNROOF

23 - 109

SUNSHADE (Continued)

WEATHERSTRIP/SEALS

TABLE OF CONTENTS

page

page

DOOR OPENING WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 110

DRIP RAIL WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 111

FRONT DOOR GLASS RUN WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 111

FRONT DOOR MOUNTED WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 112

REAR DOOR BODY MOUNTED

WEATHERSTRIP
REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 112

REAR DOOR GLASS RUN WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 113

REAR DOOR MOUNTED WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 114

TRUNK OPENING WEATHERSTRIP

REMOVAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . 114

DOOR OPENING
WEATHERSTRIP

REMOVAL

(1) Remove door opening sill plate (Refer to 23 -

BODY/INTERIOR/DOOR SILL TRIM - REMOVAL).

(2) Pull body mounted weatherstrip from fence

around door opening (Fig. 1).

INSTALLATION

(1) Position color dot on weatherstrip at the B-pil-

lar upper corner.

(2) Engage weatherstrip on the fence at upper

B-pillar and work down the B-pillar.

(3) Engage weatherstrip along the header and

down the A-pillar.

(4) Engage weatherstrip along the sill. There may

be slack material work it to the front of the opening.

(5) Verify weatherstrip sealing.

DRIP RAIL WEATHERSTRIP

REMOVAL

(1) Open front and rear doors.
(2) Remove fasteners attaching drip rail weather-

strip to body and fender tip. (Fig. 2).

(3) Remove drip rail weatherstrip from vehicle.

Fig. 1 FRONT DOOR BODY MOUNTED

WEATHERSTRIP

1 - FRONT DOOR OPENING
2 - FRONT DOOR BODY MOUNTED WEATHERSTRIP
3 - PINCH FLANGE

23 - 110

WEATHERSTRIP/SEALS

LH

INSTALLATION

(1) Place drip rail weatherstrip in position on vehi-

cle.

(2) Start position clip at the fender tip.
(3) Press down till holes are align with fastener

holes in the body.

(4) Install fasteners to attach drip rail weather-

strip to roof rail.

(5) Close doors and verify fit.

FRONT DOOR GLASS RUN
WEATHERSTRIP

REMOVAL

(1) Remove door glass (Refer to 23 - BODY/DOOR

- FRONT/DOOR GLASS - REMOVAL).

(2) Loosen side view mirror.
(3) Pull weatherstrip from lower front channel

above door latch.

(4) Pull run weatherstrip from window frame

channel (Fig. 3).

INSTALLATION

(1) Clean butyl material from door flange area.
(2) Place door run weatherstrip in position on win-

dow frame channel.

(3) Push door run weatherstrip into window frame

channel.

(4) Push weatherstrip into lower front channel

above door latch.

(5) Install door glass (Refer to 23 - BODY/DOOR -

FRONT/DOOR GLASS - INSTALLATION).

(6) Tighten side view mirror.

Fig. 3 DOOR GLASS RUN WEATHERSTRIP

1 - FRONT DOOR MOLDING
2 - GLASS RUN WEATHERSTRIP
3 - REAR GLASS RUN CHANNEL

4 - FRONT DOOR
5 - FRONT GLASS RUN CHANNEL

Fig. 2 DRIP RAIL WEATHERSTRIP

1 - A-PILLAR
2 - WINDSHIELD
3 - FASTENERS
4 - DRIP RAIL WEATHER-STRIP
5 - FASTENERS

LH

WEATHERSTRIP/SEALS

23 - 111

DRIP RAIL WEATHERSTRIP (Continued)

FRONT DOOR MOUNTED
WEATHERSTRIP

REMOVAL

(1) Using a fork type prying tool, disengage push

pin fasteners attaching weatherstrip to lower door
(Fig. 4).

(2) Remove weatherstrip from door.

INSTALLATION

(1) Place door mounted weatherstrip in position.
(2) Engage push pin fasteners to attach weather-

strip to lower door.

(3) Verify door alignment and seal

REAR DOOR BODY MOUNTED
WEATHERSTRIP

REMOVAL

(1) Remove door opening sill plate (Refer to 23 -

BODY/INTERIOR/DOOR SILL TRIM - REMOVAL).

(2) Pull body mounted weatherstrip from fence

around door opening (Fig. 5).

INSTALLATION

(1) Position color dot on weatherstrip at the B-pil-

lar upper corner.

(2) Engage weatherstrip on the fence at upper

B-pillar and work down the B-pillar.

(3) Engage weatherstrip along the header and

down the C-pillar.

(4) Engage weatherstrip along the sill. There may

be slack material, work the slack material to the
front of the opening.

(5) Install the door opening sill plate (Refer to 23 -

BODY/INTERIOR/DOOR SILL TRIM - INSTALLA-
TION).

(6) Verify weatherstrip sealing.

Fig. 4 FRONT DOOR MOUNTED WEATHERSTRIP

1 - FRONT DOOR
2 - PUSH-IN FASTENERS

Fig. 5 REAR DOOR BODY MOUNTED

WEATHERSTRIP

1 - REAR DOOR OPENING
2 - REAR DOOR BODY MOUNTED WEATHERSTRIP
3 - PINCH FLANGE

23 - 112

WEATHERSTRIP/SEALS

LH