Chrysler 300M, Dodge Interpid. Manual — part 359
CENTER CONSOLE BEZEL -
WOOD TRIM
REMOVAL - WOOD TRIM
(1) Remove the center console bezel. (Refer to 23 -
BODY/INTERIOR/CENTER
CONSOLE
BEZEL
-
REMOVAL)
(2) Remove the nuts (Fig. 9).
(3) Remove the wood trim from the bezel (Fig. 10).
INSTALLATION - WOOD TRIM
(1) Attach the wood trim to the bezel.
CAUTION: Do not over tighten the nuts or damage
to the wood trim may occur.
(2) Install the nuts.
(3) Install the center console bezel. (Refer to 23 -
BODY/INTERIOR/CENTER
CONSOLE
BEZEL
-
INSTALLATION)
Fig. 8 FRONT FLOOR CONSOLE SIDE PANELS -
INTREPID SHOWN - 300M SIMILAR
1 - INSTRUMENT PANEL
2 - FLOOR CONSOLE BEZEL
3 - POWER OUTLET/CIGAR LIGHTER CONNECTORS
4 - TRANSMISSION RANGE INDICATOR ILLUMINATION
CONNECTORS
5 - REAR END CAP
6 - FLOOR CONSOLE
7 - FRONT FLOOR CONSOLE PANEL
Fig. 9 CONSOLE BEZEL WOOD TRIM
1 - CENTER CONSOL BEZEL
2 - NUTS
3 - LOCKING TAB
Fig. 10 WOOD TRIM MOUNTING
1 - CONSOLE BEZEL GENUINE WOOD TRIM
2 - CONSOLE BEZEL
3 - LOCKING TAB
LH
INTERIOR
23 - 65
CENTER CONSOLE BEZEL (Continued)
CENTER CONSOLE
CUPHOLDER ASSEMBLY
REMOVAL - CONCORD
(1) Remove shift knob.
(2) Remove floor console shift bezel (Fig. 7).
(3) Raise console armrest lid.
(4) Remove screws at top and bottom of cup
attaching assembly (Fig. 11).
(5) Lift up and forward to remove assembly.
INSTALLATION
(1) Place cup attaching into floor console and align
screw holes.
(2) Install upper and lower screws.
(3) Lower console armrest lid.
(4) Install floor console shift bezel.
(5) Install shift knob.
CENTER CONSOLE LID LATCH
REMOVAL
(1) Open armrest lid.
(2) Remove latch attaching screws.
(3) Remove latch from console.
INSTALLATION
(1) Place latch in position.
(2) Install screws attaching latch to console.
(3) Check operation of latch.
CENTER CONSOLE REAR
BEZEL
REMOVAL
(1) Disengage tabs on sides at bottom (Fig. 12)
(2) Open arm rest lid and remove rear end cap
attaching screws.
(3) Remove rear bezel.
INSTALLATION
(1) Align rear end cap in position on console.
(2) Install rear end cap attaching screws.
(3) Push forward at the bottom to lock tabs in
position.
Fig. 11 FLOOR CONSOLE CUP HOLDER ASSEMBLY
1 - SCREWS
2 - ARMREST LID
3 - SCREW HOLES
Fig. 12 FLOOR CONSOLE END CAP
1 - FASTENERS
2 - LOCATOR PINS
3 - TABS
23 - 66
INTERIOR
LH
CENTER CONSOLE SIDE
PANELS
REMOVAL
REMOVAL - CONCORD
(1) Remove shift knob.
(2) Remove floor console shift bezel (Fig. 7).
(3) For right side panel , open the glove box door
and remove side panel screws
(4) For left side panel, remove steering column
cover and side panel screws.
(5) Disengage clips from floor console.
(6) Remove floor console side panel(s).
REMOVAL
(1) Remove shift knob.
(2) Remove console shift bezel (Fig. 8).
(3) To remove right side panel, open glove box and
remove side panel attaching screws.
(4) To remove left side panel, remove steering col-
umn cover and remove side panel attaching screws.
(5) Disengage clips from center console.
(6) Remove floor console side panel.
INSTALLATION
INSTALLATION - CONCORD
(1) Place front floor console side panel in position
on vehicle.
(2) Press on the side panel to seat clips.
(3) Install side panel(s) screws.
(4) Install floor console shift bezel.
(5) Install shift knob.
INSTALLATION
(1) Place front floor console side panel in position
on vehicle.
(2) Press on the side panel to seat clips.
(3) Install attaching screws.
(4) Install floor console shift bezel.
(5) Install shift knob.
DOOR SILL TRIM
REMOVAL
The door sills are attached with push pin fasten-
ers.
(1) Disengage fasteners attaching door sill trim to
sill panel (Fig. 13).
(2) Remove sill trim from vehicle.
INSTALLATION
(1) Place sill trim in position on vehicle.
(2) Seat fasteners to attach door sill trim to sill
panel.
FLOOR CONSOLE
REMOVAL
(1) Remove shift knob.
(2) Remove floor console shift bezel.
(3) Remove side panels (Fig. 14), or (Fig. 15).
(4) Disconnect the electrical connectors.
(5) Remove fasteners attaching forward bracket to
instrument panel.
(6) Remove fasteners attaching bottom of console
storage bin to rear mounting bracket (Fig. 16).
(7) Remove floor console from vehicle.
Fig. 13 DOOR SILL TRIM
1 - FASTENERS
2 - DOOR SILL TRIM
3 - DOOR OPENING SILL
LH
INTERIOR
23 - 67
INSTALLATION
(1) If power tap wire harness was removed reat-
tach the harness with tape, along the indicated
markings.
(2) If previously removed, install the power outlet
tap. (Refer to 8 - ELECTRICAL/POWER DISTRIBU-
TION/CIGAR
LIGHTER
OUTLET
-
INSTALLA-
TION)
(3) Place center console in position on vehicle.
(4) Install fasteners attaching forward bracket to
instrument panel.
(5) Install fasteners attaching bottom of console
storage bin to rear mounting bracket.
(6) Connect the electrical connectors.
(7) Install side panels.
(8) Install center console shift bezel.
(9) Install shift knob.
Fig. 14 FRONT FLOOR CONSOLE SIDE PANELS - CONCORDE
1 - INSTRUMENT PANEL
2 - FASTENERS
3 - CLIPS
4 - SIDE PANEL
Fig. 15 FRONT FLOOR CONSOLE SIDE PANELS
1 - INSTRUMENT PANEL
2 - FLOOR CONSOLE BEZEL
3 - POWER OUTLET/CIGAR LIGHTER CONNECTORS
4 - TRANSMISSION RANGE INDICATOR ILLUMINATION
CONNECTORS
5 - REAR END CAP
6 - FLOOR CONSOLE
7 - FRONT FLOOR CONSOLE PANEL
23 - 68
INTERIOR
LH
FLOOR CONSOLE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст