Chrysler 300M, Dodge Interpid. Manual — part 299
(12) Remove long stub shaft bearing snap ring
(Fig. 25).
(13) Remove long stub shaft and bearing from bell-
housing using Tools 8420A and C-3752 (Fig. 26).
(14) Remove oil pump-to-case bolts (Fig. 27).
Fig. 24 Low/Reverse Accumulator Components
1 - ACCUMULATOR PISTON
2 - SEAL RINGS
3 - RETURN SPRINGS
4 - (NOTE NOTCH)
Fig. 25 Remove Long Stub Shaft Snap Ring
1 - SNAP RING
2 - SNAP RING PLIERS
3 - LONG STUB SHAFT
Fig. 26 Remove Long Stub Shaft From Bellhousing
1 - LONG STUB SHAFT
2 - SPECIAL TOOL 8420A
3 - SLIDE HAMMER C-3752
Fig. 27 Remove Oil Pump Attaching Bolts
1 - BELLHOUSING
2 - OIL PUMP
LH
TRANSAXLE
21 - 15
42LE AUTOMATIC TRANSAXLE (Continued)
(15) Remove oil pump using C-3752 Pullers (Fig.
28).
(16) Remove oil pump while pushing in on input
shaft (Fig. 29).
(17) Remove oil pump gasket (Fig. 30).
CAUTION: By-pass valve must be replaced if trans-
mission failure occurs.
(18) Remove cooler by-pass valve (Fig. 31).
Fig. 28 Oil Pump Pullers
1 - OIL PUMP
2 - PULLERS
Fig. 29 Remove Oil Pump
1 - “PUSH IN” ON INPUT SHAFT WHILE REMOVING PUMP
Fig. 30 Remove Oil Pump Gasket
1 - BELL HOUSING
2 - OIL PUMP GASKET
Fig. 31 Remove By-Pass Valve
1 - BYPASS VALVE
21 - 16
TRANSAXLE
LH
42LE AUTOMATIC TRANSAXLE (Continued)
(19) Remove #1 caged needle bearing (Fig. 32).
(20) Remove input clutch assembly (Fig. 33).
(21) Remove #4 thrust plate (Fig. 34).
(22) Remove front sun gear assembly and #4
thrust washer (if still in place) (Fig. 35).
Fig. 32 Remove No. 1 Caged Needle Bearing
1 - #1 CAGED NEEDLE BEARING
2 - NOTE: TANGED SIDE OUT
Fig. 33 Remove Input Clutch Assembly
1 - INPUT CLUTCH ASSEMBLY
Fig. 34 Remove #4 Thrust Plate
1 - OVERDRIVE SHAFT ASSEMBLY
2 - #4 THRUST PLATE (SELECT)
3 - 3 DABS OF PETROLATUM FOR RETENTION
Fig. 35 Remove Front Sun Gear Assembly
1 - FRONT SUN GEAR ASSEMBLY
2 - #4 THRUST WASHER (FOUR TABS)
LH
TRANSAXLE
21 - 17
42LE AUTOMATIC TRANSAXLE (Continued)
(23) Remove front carrier/rear annulus and #6 nee-
dle bearing (Fig. 36).
(24) Remove rear sun gear and #7 needle bearing
(Fig. 37) (Fig. 38).
NOTE: The number seven needle bearing has three
antireversal tabs and is common with the number
five and number two position. The orientation
should allow the bearing to seat flat against the
rear sun gear (Fig. 38). A small amount of petrola-
tum can be used to hold the bearing to the rear sun
gear.
(25) Install and load Tool 5058 to remove 2/4
clutch retainer snap ring (Fig. 39).
Fig. 36 Remove Front Carrier/Rear Annulus
1 - #6 NEEDLE BEARING
2 - FRONT CARRIER AND REAR ANNULUS ASSEMBLY (TWIST
AND PULL OR PUSH TO REMOVE OR INSTALL).
Fig. 37 Remove Rear Sun Gear
1 - #7 NEEDLE BEARING
2 - REAR SUN GEAR
Fig. 38 Number 7 Bearing
1 - #7 BEARING
2 - REAR SUN GEAR
Fig. 39 Remove 2/4 Clutch Retainer Snap Ring
1 - TOOL 5058
2 - SCREWDRIVER
3 - SNAP RING
4 - 2/4 CLUTCH RETAINER
21 - 18
TRANSAXLE
LH
42LE AUTOMATIC TRANSAXLE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст