Chrysler 300M, Dodge Interpid. Manual — part 356
1 - SPEAKER, INSTRUMENT PANEL CENTER
11 - BEZEL INSTRUMENT CLUSTER
2 - INSTRUMENT PANEL ASSEMBLY
12 - SWITCH HEADLAMP
3 - BEZEL, INSTRUMENT PANEL END CAP
13 - LOUVER, AIR OUTLET
4 - LOUVER, AIR OUTLET
14 - COVER, INSTRUMENT PANEL CENTER SUPPORT/BIN (6 PASS. ONLY)
5 - HOUSING INSTRUMENT CLUSTER
15 - 6 PASS. ONLY
6 - GLOVE BOX ASSEMBLY
16 - ASH RECEIVER
7 - RADIO
17 - LEVER, PARKING BRAKE
8 - CONTROL ASSEMBLY, INSTRUMENT PANEL
18 - COVER, LOWER INSTRUMENT PANEL
9 - LOUVER, AIR OUTLET
19 - BEZEL, INSTRUMENT PANEL END CAP
10 - BEZEL, INSTRUMENT PANEL TRIM-CENTER
20 - COVER, UPPER INSTRUMENT PANEL
LH
INSTRUMENT PANEL
23 - 53
INSTRUMENT PANEL ASSEMBLY (Continued)
Fig. 8 INSTRUMENT PANEL COMPONENTS - CONCORDE
23 - 54
INSTRUMENT PANEL
LH
INSTRUMENT PANEL ASSEMBLY (Continued)
INSTALLATION
(1) If replacing instrument panel and pad assem-
bly, transfer all parts to new assembly (Fig. 6), (Fig.
7), and (Fig. 8).
(2) With the help of an assistant, place instrument
panel into vehicle into the approximate mounting
position (Fig. 5).
(3) Make sure that all harnesses are free and clear
from snagging.
(4) Install eight instrument panel retaining screws
to body.
(5) Connect the left side harness connectors to
junction block and Body Control Module (BCM).
(6) Connect the two right side harness connectors
to radio antenna and amplifier DIN cable.
(7) Install the right side under dash silencer/pad.
(8) Place the right and left cowl side kick panels
into position and install the three retaining screws.
(9) Place the right and left scuff plates into posi-
tion and firmly press them into place. Install the one
screw retaining each left and right scuff plate.
(10) Place the instrument panel top cover into
position and firmly snap into place (Fig. 5).
(11) Place the right and left A-pillar trim moldings
into place starting from the rear and firmly snap into
place.
(12) Connect the two harness connectors to the
HVAC housing, the Airbag Control Module (ACM),
and two ground eyelets left of the floor tunnel near
the bulkhead.
(13) Install the steering column:
(a) Raise steering column into position at brake
pedal support bracket.
(b) Install the four column mounting bolts at
brake pedal support bracket.
(c) Place the left panel A/C outlet duct into posi-
tion and firmly snap into place.
(d) Place the under column duct section into
position and firmly snap into place.
(e) Connect column wiring.
(f) Connect
shift
interlock
cable
at
ignition
switch.
(g) Install the steering column shrouds.
(14) Install one screw attaching instrument panel
to the steering column mounting plate (Fig. 4).
(15) Place the left floor duct/silencer pad into posi-
tion and install the one retaining screw.
(16) Connect the 16-way Diagnostic Link Connec-
tor (DLC) to the steel reinforcement.
(17) Install the four bolts to steel reinforcement at
the bottom of lower instrument panel cover.
(18) Install the two nuts attaching center lower
instrument panel to floor tunnel bracket. On six pas-
senger vehicles go to Step 25 (Fig. 3).
(19) Install the two front bracket screws and two
screws inside console storage bin to console.
(20) Place the right console side cover into position
and firmly snap into place. Install the two screws to
right console side cover.
(21) Raise glove box door to by pinching sides
together, towards each other.
(22) Place the left console side cover into position
and firmly snap into place. Install the two screws to
the left console side cover.
(23) Connect wire connectors to HVAC control and
traction control switch.
(24) On five passenger vehicles, place instrument
panel center bezel into position and firmly snap into
place (Refer to 23 - BODY/INSTRUMENT PANEL/
STORAGE BIN - INSTALLATION).
(25) On six passenger vehicles, install the lower
floor bin (Refer to 23 - BODY/INSTRUMENT PAN-
EL/STORAGE BIN - INSTALLATION).
(26) Connect decklid release switch wiring connec-
tor, install the cable to brake release handle. Place
the left lower instrument panel cover into position
and firmly snap into place. Install the two screws to
the lower instrument panel cover (outside end).
(27) Connect two wire connectors and one illumi-
nation bulb socket.
(28) Place shifter bezel into position and firmly
snap into place.
NOTE: On 300M vehicles, the shifter bezel must be
installed prior to the center bezel being installed.
(29) Install left and right instrument panel end
covers by placing into position and firmly snapping
into place.
(30) Install the one Allen screw to shifter knob.
(31) Connect the negative battery cable remote ter-
minal to the remote battery post (Fig. 1).
1 - SPEAKER, INSTRUMENT PANEL CENTER
10 - BEZEL, INSTRUMENT CLUSTER
2 - COVER, UPPER INSTRUMENT PANEL
11 - SWITCH, HEADLAMP
3 - INSTRUMENT PANEL ASSEMBLY
12 - LOUVER, AIR OUTLET
4 - BEZEL, INSTRUMENT PANEL END CAP
13 - COVER, INSTRUMENT PANEL CENTER SUPPORT/BIN (6 PASS. ONLY)
5 - LOUVER, AIR OUTLET
14 - ASH RECEIVER
6 - GLOVE BOX ASSEMBLY
15 - BEZEL, INSTRUMENT PANEL TRIM - CENTER
7 - CONTROL ASSEMBLY, INSTRUMENT PANEL
16 - LEVER, PARKING BRAKE
8 - HOUSING, INSTRUMENT CLUSTER
17 - COVER, LOWER INSTRUMENT PANEL
9 - RADIO
18 - BEZEL, INSTRUMENT PANEL END CAP
LH
INSTRUMENT PANEL
23 - 55
INSTRUMENT PANEL ASSEMBLY (Continued)
INSTRUMENT PANEL CENTER
BEZEL
REMOVAL
(1) Open hood and disconnect the negative battery
cable remote terminal from the remote battery post
(Fig. 1).
(2) Remove ash receiver (if applicable).
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry out on center trim bezel. Dis-
connect wiring connectors to HVAC controls, cigar
lighter/auxiliary power outlet and traction control
switch (if equipped) (Fig. 9).
(4) Remove instrument panel center trim bezel.
NOTE: The traction control switch, HVAC control
head and cigar lighter/auxiliary power outlet must
be transferred to new bezel if being replaced.
INSTALLATION
(1) Connect wiring connectors to HVAC controls,
cigar lighter/auxiliary power outlet and traction con-
trol switch (if equipped).
(2) Place the instrument panel center trim bezel
into position and firmly snap into place (Fig. 9).
(3) Install the ash receiver (if equipped).
(4) Connect the negative battery cable remote ter-
minal to the remote battery post (Fig. 1).
INSTRUMENT PANEL END CAP
REMOVAL
(1) Open the left door and pull on the access han-
dle to disengage the end cap clips. Fuse diagram is
located inside the left end cap. Fuse Access is under
the left end cap (Fig. 10).
(2) Open the right door and remove the right end
cover by inserting a trim stick (special tool #C-4755),
between cap and instrument panel to disengage clips.
INSTALLATION
(1) Pull body mounted weatherstrip form fence
along the side of the instrument panel.
(2) Align the end cap with the retaining slots in
instrument panel and firmly snap into place (Fig.
10).
(3) Engage weatherstrip along the header and
down the A-pillar.
(4) Verify weatherstrip sealing.
(5) Close door.
INSTRUMENT PANEL
SILENCER
REMOVAL
(1) Remove the retaining screw to the instrument
panel.
(2) Maneuver part and bracket off of the center
floor distribution duct.
(3) Remove the silencer/duct.
INSTALLATION
(1) Install the silencer/duct.
(2) Maneuver part and bracket on to the center
floor distribution duct.
(3) Install the retaining screw to the instrument
panel.
Fig. 9 INSTRUMENT PANEL CENTER UPPER BEZEL
1 - INSTRUMENT PANEL
2 - INSTRUMENT PANEL BEZEL
3 - CONSOLE
4 - CONSOLE SIDE PANEL
Fig. 10 INSTRUMENT PANEL END COVER
1 - INSTRUMENT PANEL END COVER
2 - INSTRUMENT PANEL
23 - 56
INSTRUMENT PANEL
LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст