Chrysler 300M, Dodge Interpid. Manual — part 2
FASTENER USAGE
DESCRIPTION
DESCRIPTION - FASTENER USAGE
WARNING: USE OF AN INCORRECT FASTENER
MAY RESULT IN COMPONENT DAMAGE OR PER-
SONAL INJURY.
Fasteners and torque specifications references in
this Service Manual are identified in metric and SAE
format.
During any maintenance or repair procedures, it is
important to salvage all fasteners (nuts, bolts, etc.)
for reassembly. If the fastener is not salvageable, a
fastener of equivalent specification must be used.
DESCRIPTION - THREADED HOLE REPAIR
Most stripped threaded holes can be repaired using
a Helicoil
t. Follow the vehicle or Helicoilt recommen-
dations for application and repair procedures.
INTERNATIONAL SYMBOLS
DESCRIPTION
The graphic symbols illustrated in the following
International Control and Display Symbols Chart
(Fig. 5) are used to identify various instrument con-
trols. The symbols correspond to the controls and dis-
plays that are located on the instrument panel.
Fig. 5 INTERNATIONAL CONTROL AND DISPLAY SYMBOLS
1
High Beam
13
Rear Window Washer
2
Fog Lamps
14
Fuel
3
Headlamp, Parking Lamps, Panel Lamps
15
Engine Coolant Temperature
4
Turn Warning
16
Battery Charging Condition
5
Hazard Warning
17
Engine Oil
6
Windshield Washer
18
Seat Belt
7
Windshield Wiper
19
Brake Failure
8
Windshield Wiper and Washer
20
Parking Brake
9
Windscreen Demisting and Defrosting
21
Front Hood
10
Ventilating Fan
22
Rear hood (Decklid)
11
Rear Window Defogger
23
Horn
12
Rear Window Wiper
24
Lighter
LH
INTRODUCTION
5
METRIC SYSTEM
DESCRIPTION
The metric system is based on quantities of one,
ten, one hundred, one thousand and one million.
The following chart will assist in converting metric
units to equivalent English and SAE units, or vise
versa.
CONVERSION FORMULAS AND EQUIVALENT VALUES
MULTIPLY
BY
TO GET
MULTIPLY
BY
TO GET
in-lbs
x
0.11298
= Newton Meters
(N·m)
N·m
x 8.851
= in-lbs
ft-lbs
x
1.3558
= Newton Meters
(N·m)
N·m
x
0.7376
= ft-lbs
Inches Hg (60° F)
x 3.377
= Kilopascals (kPa)
kPa
x
0.2961
= Inches Hg
psi
x 6.895
= Kilopascals (kPa)
kPa
x 0.145
= psi
Inches
x 25.4
= Millimeters (mm)
mm
x
0.03937
= Inches
Feet
x
0.3048
= Meters (M)
M
x 3.281
= Feet
Yards
x
0.9144
= Meters
M
x
1.0936
= Yards
mph
x
1.6093
= Kilometers/Hr.
(Km/h)
Km/h
x
0.6214
= mph
Feet/Sec
x
0.3048
= Meters/Sec (M/S)
M/S
x 3.281
= Feet/Sec
mph
x
0.4470
= Meters/Sec (M/S)
M/S
x 2.237
= mph
Kilometers/Hr. (Km/h)
x
0.27778
= Meters/Sec (M/S)
M/S
x 3.600
Kilometers/Hr. (Km/h)
COMMON METRIC EQUIVALENTS
1 inch = 25 Millimeters
1 Cubic Inch = 16 Cubic Centimeters
1 Foot = 0.3 Meter
1 Cubic Foot = 0.03 Cubic Meter
1 Yard = 0.9 Meter
1 Cubic Yard = 0.8 Cubic Meter
1 Mile = 1.6 Kilometers
Refer to the Metric Conversion Chart to convert
torque values listed in metric Newton- meters (N·m).
Also, use the chart to convert between millimeters
(mm) and inches (in.) (Fig. 6).
6
INTRODUCTION
LH
Fig. 6 METRIC CONVERSION CHART
LH
INTRODUCTION
7
METRIC SYSTEM (Continued)
TORQUE REFERENCES
DESCRIPTION
Individual Torque Charts appear within many or the
Groups. Refer to the Standard Torque Specifications
Chart for torque references not listed in the individual
torque charts (Fig. 7).
Fig. 7 TORQUE SPECIFICATIONS
8
INTRODUCTION
LH
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст