Chrysler Town & Country/Voyager, Dodge Caravan, Plymouth Voyager. Manual — part 212
(1) Liftgate release switch operates with a push-on
momentary action. The switch operates a relay to
provide power to the liftgate solenoid. Vehicle must be
in Park or Neutral and not moving for liftgate release
switch to operate.
(2) The rear window defogger operates with a
push-on and push-off momentary action. The switch
portion of the carrier consists of a timer circuit, relay
and a power management circuit. An amber indicator
on the button shows when the switch is ON. Once the
rear window defogger is ON, the system shall remain
on until one of the following occurs:
• The switch is actuated again by push-off action.
• Ten minutes 62 minutes has elapsed since the
switch has been actuated
• The liftgate release switch is actuated. Under this
condition, the rear window defogger relay contact is
temporary opened until the liftgate switch is released.
This power management circuit prevents the printed
circuit board of the accessory switch carrier from being
damage by too much current flow.
(3) Fog lamp switch operates with a push-on and
push-off momentary action. The switch portion of the
carrier has a relay and an electronic latching circuit
and the following:
• A green indicator on the button shows when the
switch in ON.
• Fog lamps can be turned on only when the head-
lamps are on low beams.
(4) Power to the rear passenger compartment is
controlled by the rear A/C header blower switch. The
switch operates by a horizontal sliding action. The
switch has four clearly defined detent positions:
Fig. 30 Accessory Switch Carrier
Fig. 28 Headlamp POD Switch Continuity Test
Fig. 29 Rear Wiper/Washer Control POD Switch
.
INSTRUMENT PANEL AND GAUGES
8E - 13
(a) The left most detent is OFF position.
(b) The second detent from the left is the ON
position. The ON position supplies power to the
switch in the rear passenger compartment. When the
switch is in any other position than ON, the rear
passenger compartment switch is over ridden.
(c) The third detent from the left is the Low
position.
(d) The fourth detent at the full right is the High
position.
ACCESSORY SWITCH CARRIER TEST
(1) Remove switch, refer to switch replacement.
(2) Using a volt/ohm meter, refer to Fig. 31 for
testing of wire end of connector while connected to
switch.
(3) Refer to Fig. 32 to test A/C heater switch. If
continuity is not correct replace A/C heater switch.
ACCESSORY SWITCH CARRIER REPLACEMENT
(1) Remove center bezel using a trim stick from
instrument panel (Fig. 33).
(2) Remove ash receiver lamp socket from bezel.
(3) Remove accessory switch carrier from the panel
(Fig. 30).
(4) Disconnect wire connectors and lamp.
(5) For installation reverse above procedures.
A/C AND HEATER CONTROL/BLOWER SWITCH
REPLACEMENT
(1) Remove center bezel using a trim stick from
instrument panel (Fig. 33).
(2) Remove ash receiver lamp socket from bezel.
(3) Remove cigar lighter element.
(4) Remove accessory switch carrier.
(5) Remove two screws and pull control assembly
rearward. Reach behind control and disconnect the
wiring harnesses, vacuum lines and temperature con-
trol cable (Fig. 34).
(6) For installation reverse above procedures.
A/C AND HEATER CONTROL LAMP REPLACE-
MENT
(1) Remove center bezel using a trim stick from
instrument panel (Fig. 33).
(2) Remove ash receiver lamp socket from bezel.
(3) Remove cigar lighter element.
(4) Remove accessory switch carrier.
(5) Remove two screws and pull control assembly
rearward. Reach behind control and disconnect lamp
(Fig. 34).
(6) For installation reverse above procedures.
Fig. 31 Accessory Switch Carrier Test
Fig. 32 A/C Heater Switch Test
8E - 14
INSTRUMENT PANEL AND GAUGES
.
REAR A/C-HEATER SWITCH REPLACEMENT
For the blower switch on the instrument panel, refer
to Accessory Switch Carrier Replacement (Fig. 30).
The rear A/C-heater switch assembly in the left rear
quarter trim panel (Fig. 34).
(1) Using a trim stick pry switch from left quarter
trim panel.
(2) Disconnect wire connectors.
(3) For installation reverse above procedures.
CIGAR LIGHTER REPLACEMENT
(1) Disconnect battery
(2) Remove cigar lighter element.
(3) Remove center trim bezel. Remove ash receiver
lamp and socket if a equipped.
(4) Remove
accessory
switch
carrier
attaching
screws.
(5) Remove A/C heater control attaching screws. Pull
out and disconnect the wire connector and control
cable(s).
(6) Disconnect wire connectors and lamp/socket from
rear of cigar lighter clamp.
(7) Hold outer clamp, while turning shell. Do not
lose cigar lighter shield (Fig. 36).
(8) For installation reverse above procedures.
FORWARD CONSOLE REMOVAL
(1) Remove center bezel using a trim stick from
instrument panel (Fig. 33).
(2) Remove ash receiver lamp socket from bezel.
(3) Remove filler plate (Fig. 37).
(4) Remove ash receiver/cup holding assembly from
console. Refer to Ash Receiver Assembly for removal.
(5) Remove screws attaching console to instrument
panel:
• Two upper corners
• Two behind ash receiver
Fig. 33 Center Bezel
Fig. 34 A/C Heater Control
Fig. 35 Rear A/C Heater Control Switch
.
INSTRUMENT PANEL AND GAUGES
8E - 15
• Two at the lower bracket
(6) Pull console rearward and disconnect wire con-
nector and bulb.
(7) Remove console.
(8) For installation reverse above procedures.
CENTER STORAGE MODULE REMOVAL
(1) Remove center bezel using a trim stick from
instrument panel (Fig. 33).
(2) Remove ash receiver lamp socket from bezel.
(3) Remove ash receiver/cup holding assembly from
console. Refer to Ash Receiver Assembly for removal.
(4) Open the storage bin door and remove the check
strap pins so that door swings fully open.
(5) Remove four mounting screws and storage mod-
ule.
(6) For installation reverse above procedures.
ASH RECEIVER ASSEMBLY
Depress the ash receiver/cupholder assembly stops
and remove by sliding rearward.
BODY CONTROLLER REPLACEMENT
(1) Remove steering column cover to gain access to
the body controller (Fig. 38).
(2) Disconnect the two 25-way connectors from body
controller.
(3) Remove mounting screws from body controller.
(4) Pull to the left to release body controller of S-clips
and remove unit.
(5) For installation reverse above procedures. En-
sure body controller is locked into the S-clips.
LOWER RIGHT INSTRUMENT PANEL REPLACE-
MENT
(1) Remove center console bezel using a trim stick
from instrument panel (Fig. 33).
(2) Remove accessory switch carrier.
(3) Remove heater control (Fig. 34).
(4) Disconnect cigar lighter.
(5) Remove center or forward console, refer to re-
moval procedures (Fig. 36).
(6) Remove attaching screws and right lower panel
(Fig. 39).
Fig. 36 Cigar Lighter
Fig. 37 Forward and Center Console
Fig. 38 Instrument Panel Steering Column Cover
8E - 16
INSTRUMENT PANEL AND GAUGES
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст