SsangYong Korando II (1996-2006 year). Manual — part 123
1F2 -- 72 M161 ENGINE CONTROLS
DAEWOO MY_2000
COOLING FAN
KAB1F290
Failure
Code
Description
Trouble Area
Maintenance Hint
44
Cooling fan (HI) relay
short circuit to power
Cooling fan short circuit to
power
D
Inspection the Engine Control Module
(ECM) pin 35 about short circuit or
open with bad contact
45
Cooling fan (HI) relay
short circuit to ground or
open
Cooling fan short circuit to
ground or open
open with bad contact
D
Inspection the power source
D
Inspection the cooling fan
D
Inspection the ECM
Circuit Description
Ignition voltage is supplied directly to the cooling fan relay coil. The ECM controls the relay by grounding the control
circuit. When the ECM is commanding a command ON, the voltage of the control circuit should be low (near 0 volt).
When the ECM is commanding the control circuit should be high (near battery voltage). If the fault detection circuit
senses a voltage other than what is expected, the fault line status will change causing the fault code to set.
M161 ENGINE CONTROLS 1F2 -- 73
DAEWOO MY_2000
A/C COMPRESSOR RELAY
KAB1F290
Failure
Code
Description
Trouble Area
Maintenance Hint
228
A/C compressor relay
short circuit to battery
When malfunction of A/C
D
Monitoring the actual operation
through scan tool
D
Inspection the Engine Control Module
(ECM) pin 44 about short circuit or
229
A/c compressor relay
short circuit to ground or
open
When malfunction of A/C
compressor control
(ECM) pin 44 about short circuit or
open with bad contact
D
Inspection the relay short circuit or
open
D
Inspection the ECM
Circuit Description
When the ECM detects that A/C has been requested, the ECM will activated the A/C clutch relay. When the relay has
been activated, voltage should be present at both the A/C clutch relay and A/C switch circuit at ECM.
1F2 -- 74 M161 ENGINE CONTROLS
DAEWOO MY_2000
CRUISE CONTROL SWITCH
KAB1F300
Failure
Code
Description
Trouble Area
Maintenance Hint
129
Cruise control “OFF”
due to message counter
failure
Cruise control system
Message counter fault
130
Vehicle speed signal
failure
When malfunction of
auto--cruise system
D
Monitoring the actual recognition
status and vehicle speed signal
through scan tool
131
Vehicle speed signal
failure
auto cruise system
Implausible condition of
vehicle speed signal.
through scan tool
D
Inspection the Engine Control Module
(ECM) pin 52, 53, 54, 55, 57 about
132
Cruise control lever
failure
Cruise control lever defective
(ECM) pin 52, 53, 54, 55, 57 about
short circuit or open with bad contact
D
Inspection the CAN and ABS
133
Cruise control
acceleration failure
Cruise control system
Implausible condition of
acceleration signal
Inspection the CAN and ABS
D
Inspection the cruise control lever
switch
D
Inspection the ECM
134
Cruise control
deceleration failure
Cruise control system
Implausible condition of
deceleration signal
p
Circuit Description
Cruise control is an automatic speed control system that maintain a desired driving speed without using the accelerator
pedal. The vehicle speed must be greater than 40 km/h to engage cruise control.
M161 ENGINE CONTROLS 1F2 -- 75
DAEWOO MY_2000
TRACTION CONTROL SYSTEM (TCS)
KAB1F310
Failure
Code
Description
Trouble Area
Maintenance Hint
150
TCS input signal short
circuit to battery
TCS short circuit to power
D
Inspection the Engine Control Module
(ECM) pin 45 about short circuit or
open with bad contact
151
TCS input signal short
circuit to ground or open
TCS short circuit to ground or
open
open with bad contact
D
Inspection the TCS lamp of I/P cluster.
D
Inspection the ECM
Circuit Description
Battery voltage is supplied to the TCS warning lamp with the ignition in ON and START. The warning lamp can be
activated only by the Electrical Brake Control Module (EBCM) internally supplying ground to terminal 32. If the TCS
input circuit is open or short, this failure code will be set.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст