SsangYong Korando II (1996-2006 year). Manual — part 428

SSANGYONG MY2002

9D-2 WIPER, WASHER SYSTEMS

DESCRIPTION AND OPERATION

WINDSHIELD WIPER SYSTEM

The windshield wiper system consists of a wiper motor,
a linkage, wiper arms and blade, and a wiper/washer
switch. The windshield wiper circuit incorporates a self
parking device which consists of a worm gear and a
camplate in order to keep the circuit engaged
temporarily when the switch is turned off. The wiper
system is driven by a permanent magnet-type motor.
The windshield wiper motor is mounted on the dash
panel and is directly con-nected to the windshield
wiper linkage.

The windshield wiper motor has two speeds, LO and
HI, and also has intermittent wiper. The wiper switch
is an integral part of the wiper/washer switch.
Windshield wiper operation is actuated through the
lever on the right side of the steering column.

WINDSHIELD WASHER SYSTEM

The windshield washer system is equipped with a
washer fluid reservoir, a washer fluid pump, hoses,
nozzles, and a wiper/washer switch. The windshield
washer reservoir is mounted above the front right apron
panel. Attached to the reservoir is a washer pump,
which pumps fluid through the hoses to the two nozzles
mounted on the hood. The washer switch is an integral
part of the wiper/washer switch. Windshield washer
operation is actuated through the lever on the right
side of the steering column.

WIPER, WASHER SYSTEMS 9D-3

SSANGYONG MY2002

COMPONENTS LOCATOR

LIGHTING SYSTEM

1 Windshield Wiper Arm
2 Windshield Wiper Motor
3 Windshield Wiper Blade
4 Windshield Washer Reservoir
5 Windshield Wiper Linkage
6 Windshield Washer Pump

7 Windshield Washer Nozzles
8 Windshield Washer Hoses
9 Rear Wiper Arm

10 Rear Wiper Motor
11 Rear Washer Reservoir

KAA9D010

SSANGYONG MY2002

9D-4 WIPER, WASHER SYSTEMS

KAA9D030

KAA9D040

3. Remove the nut and the wiper arm.

•

Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.

4. Installation should follow the removal procedure

in the reverse order.

WINDSHIELD WIPER MOTOR

Removal and Installation Procedure

1. Remove the left cowl top cover. Refer to “WIND-

SHIELD WIPER ARM” in this section.

2. Remove the center cowl top cover with the screws.

3. Remove the nut and the washer that secure the

wiper arm linkage to the motor driveshaft.

4. Pry the wiper arm linkage off the motor driveshaft.

KAA9D020

ON-VEHICLE SERVICE

UNIT REPAIR

WINDSHIELD WIPER ARM

Removal and Installation Procedure

1. Remove the left cowl top cover cap.

2. Remove the screws with the left cowl top cover.

REPAIR INSTRUCTIONS

WIPER, WASHER SYSTEMS 9D-5

SSANGYONG MY2002

KAA9D050

KAA9D060

5. Remove nuts and the wiper motor.

Installation Notice

•

Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.

6. Installation should follow the removal procedure

in the reverse order.

WINDSHIELD WASHER
RESERVOIR

Removal and Installation Procedure

1. Open the hood.

2. Disconnect the negative battery cable.

3. Remove the coolant reservoir. Refer to Section 1D,

ENGING COOLING.

4. Disconnect the washer hose from the washer

pump.

WINDSHIELD WIPER BLADE

Removal and Installation Procedure

1. Rotate the wiper blade on the arm.

2. While pressing the retainer clip, slide the wiper

blade down the wiper arm and remove the blade.

3. Installation should follow the removal procedure

in the reverse order.

Tightening Torque

8 - 12 N•m

(71 - 106 lb-ft)

KAA9D070

5. D i s c o n n e c t t h e r e s e r v o i r p u m p e l e c t r i c a l

connector.

6. Remove the bolt and the reservoir

Installation Notice

•

Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.

7. Installation should follow the removal procedure

in the reverse order.

Tightening Torque

5 - 9 N•m

(44 - 80 lb-in)