SsangYong Musso. Manual — part 296
M161 ENGINE MECHANICAL 1B2-111
Chamfering Procedure
1. Chamfer angle : 75°
2. Polish the lower chamfered area evenly with a grinder after
finishing the chamfering with a suitable tool (e.g., hand milling
cutter).
1B2-112 M161 ENGINE MECHANICAL
CYLINDER HEAD MATING SURFACE
Preceding Work : Removal of valves
Service Data Standard
Notice
Do not exceed 0.4mm for the milling of the mating surface of crankcase and cylinder head.
Overall Height of Cylinder Head
Minimum Height After Machining
Flatness
Distance ‘T’
(Between Camshaft Bearing
and Valve Stem)
Axial Direction
Transverse Direction
Standard Size
Repair Size
135.9 - 136.0 mm
135.5 mm
0.08 mm
0.0 mm
24.21 - 24.75 mm
22.21 - 22.75 mm
23.96 - 24.51 mm
21.96 - 22.51 mm
Intake
Exhaust
Intake
Exhaust
M161 ENGINE MECHANICAL 1B2-113
Measurement of Mating Surface
1. Measure the height (H) of the cylinder head (refer to Service
data standard).
2. Check the mating surface of the cylinder head.
3. Mill the sharp edge of the combustion chamber.
4. Re-measure the height (H) of the cylinder head.
5. Seal the intake and exhaust valves.
6. Measure the dimension (T) between the camshaft bearing
and the valve system (refer to Service data standard).
7. Mill the cylinder head valve seat (refer to Service data
standard).
Universal Tool
Surface Grinding Machine
Sceledum, Type RTY
Roaro
Schio/Italy
SECTION 1D1
M162 ENGINE COOLING
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1D1-1
General Specifications . . . . . . . . . . . . . . . . . 1D1-1
Fastener Tightening Specifications . . . . . . . . 1D1-2
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1D1-3
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1D1-3
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-4
System Leakage Test . . . . . . . . . . . . . . . . . . 1D1-4
Maintenance and Repair . . . . . . . . . . . . . . 1D1-5
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 1D1-5
Coolant Drain and Fill Up . . . . . . . . . . . . . . . 1D1-5
Coolant Connection Fitting . . . . . . . . . . . . . . 1D1-7
Water Pump . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-8
Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-10
Oil Cooler Pipe Line . . . . . . . . . . . . . . . . . . 1D1-11
Cooling Fan and Viscous Clutch . . . . . . . . . 1D1-12
Cooling Fan Shroud . . . . . . . . . . . . . . . . . . 1D1-14
Radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . 1D1-15
SPECIFICATIONS
GENERAL SPECIFICATIONS
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless otherwise
noted.
TABLE OF CONTENTS
Description
Water Cooling Forced Circulation
Double Cross Flow
70,000 kcal/h
580 x 482 x 45 mm
φ
460, Six Blades
ALUTEC - P78
50 : 50
11.3 L
3.4 L
1.4 bar
Application
Cooling Type
Radiator
Dimension(Width
×
Height
×
Thickeness)
Cooling Fan
Anti-Freeze Agent
Mixing Ratio of Anti-Freeze Agen with Water (Anti-Freeze Agent : Water)
Coolant Capacity
Reservoir Capacity
Cap Operating Pressure (Reservoir Tank Pressure Cap)
Circulation Type
Radiation Capability
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст