SsangYong Musso. Manual — part 429
3D-2 REAR DRIVE AXLE
FASTENER TIGHTENING SPECIFICATIONS
Application
Inner Bracket Mounting Nut
Propeller Shaft to Rear Axle Input Shaft
Lower Arm Mounting Nut
Lower Shock Absorber to Axle Housing
Upper Arm Mounting Nut
Stabilizer Bar Mounting Bolt
Lateral Rod Mounting Nut
Drive Pinion Lock Nut
Oil Drain Plug
Ring Gear Mounting Bolt
Oil Filler Plug
N
•••••
m
50 - 65
70 - 80
150 - 180
50 - 65
150 - 180
30 - 45
150 - 180
240 - 310
28 - 42
75 - 90
28 - 42
4.55
4.55
4.55
4.27
5.86
3.73
3.73
4.89
1.9 L
SEA 80W/90, API GL - 5
M/T
A/T (MB)
M/T
A/T (MB)
A/T (BTRA)
M/T
A/T (MB)
A/T (BTRA)
Oil Capacity
Oil Specification
Application
Description
GENERAL SPECIFICATIONS(CONT'D)
E20
E23
E32
Reduction Ratio
REAR DRIVE AXLE 3D-3
Checks
Worn or Damaged Tooth of Pinion or Side Gear
Worn Pinion Shaft
Excessive Backlash of Pinion Gear and Side Gear
Excessive End-play of Rear Axle Shaft
Incorrect Contact of Side Gear and Differential Case
Axle Housing Crack
Bent or Poor Installation of Drive Pinion Oil Seal
Damaged or Torn Drive Pinion Oil Seal
Loosened Bearing Collar
Worn or Damaged Universal Joint
Worn or Damaged Axle Shaft Bearing
Checks
Excessive Oil
Faulty Seal of Carrier Contact Surface
Axle Housing Crack
Worn or Damaged Oil Seal
Checks
Lack of Oil
Low Viscosity of Oil
Insufficient Oil
Excessive Backlash of Ring Gear
Worn or Damaged Tooth of Ring and Pinion Gear
Worn or Damaged Drive Pinion Bearing
Bent Axle Housing
Bent Differential Case
Worn Pinion Shaft
Incorrect Drive Pinion Preload
Incorrect Contact of Ring Gear and Pinion
DIAGNOSIS
NOISE (DURING STRAIGHT DRIVING)
Action
Replenish
Replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Adjust
Retightening
OIL LEAKAGE
Action
Adjust
Repair
Replace
Replace
NOISE (DURING TURNING)
Action
Replace
Replace
Replace
Adjust
Replace
Replace
Replace
Replace
Replace
Replace
Replace
HEATING
Checks
Lack of Oil
Insufficient Backlash of Gears
Excessive Preload of Bearing
Action
Replenish
Adjust
Adjust
3D-4 REAR DRIVE AXLE
VIBRATION
Checks
Faulty Connection of Sliding Joint
Bent Propeller Shaft
Symmetry of Universal Joint Snap Ring
Loosened Yoke Bolts
Action
Adjust
Replace
Adjust
Tighten
NOISE
Checks
Worn or Damaged Universal Joint Bearing
Fallen Off Universal Joint Snap Ring
Loosened Yoke Connection
Worn Sliding Joint Spline
Insufficient Grease
Action
Replace
Adjust or Replace
Tighten
Replace
Apply as Necessary
REAR DRIVE AXLE 3D-5
1 Spring Seat
2 Coil Spring
3 Lateral Rod
4 Shock Absorber
5 Upper Arm
6 Lower Arm
7 Connecting Link
8 Stabilizer Bar
COMPONENT LOCATOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст