SsangYong Musso. Manual — part 440
PROPELLER SHAFT 3C-7
Installation Procedure
Clean the disassembled parts and replace them if damaged.
1. Align the alignment marks of the yoke and assemble the
spider, bearing and snap ring.
2. Apply grease to the inner of the bearing cap of the needle
roller bearing and assemble the needle roller.
Grease
EP #2
6. Possible cause of vibration.
!
Drift away of balance weights.
!
Excessive runout of the propeller shaft.
!
Using normal bolts.
!
Excessive wear of the universal joint.
!
Sticks in sleeve joint.
!
Drive angle changes in universal joints or cross causes
vibration and can be detected around 60~100 km/h.
5. Universal joint starting torque.
Starting Torque
3 - 8 kg
!
cm
3C-8 PROPELLER SHAFT
3. Install the bearing cap to the yoke and insert the spider.
Install the opposite side cap by tapping with a plastic
hammer. Adjust clearance of the spider pin to be within 0.1
mm and install the snap ring.
4. Align the alignment marks and install the front and rear
propeller shaft. Tighten the nuts to the specified torque.
Gasoline
Diesel
SECTION 4A
HYDRAULIC BRAKES
Specifications . . . . . . . . . . . . . . . . . . . . . . . . 4A-1
General Specifications . . . . . . . . . . . . . . . . . . 4A-1
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Noise or Vehicle Vibration When Applied
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Pulls to One Side When Braking . . . . . . . . . . . 4A-2
Poor Braking. . . . . . . . . . . . . . . . . . . . . . . . . . 4A-2
Increasing Pedal Stroke (Pedal Goes to
Floor) or Brake Dragging . . . . . . . . . . . . . . . 4A-3
Poor Braking of Parking Brake . . . . . . . . . . . . 4A-3
TABLE OF CONTENTS
Component Locator . . . . . . . . . . . . . . . . . . . 4A-4
ABS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-4
ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-5
Non-ABS / ABD . . . . . . . . . . . . . . . . . . . . . . . . 4A-6
Maintenance and Repair . . . . . . . . . . . . . . . 4A-7
On-Vehicle Service . . . . . . . . . . . . . . . . . . . . . 4A-7
Bleeding the Brakes . . . . . . . . . . . . . . . . . . . . 4A-7
Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . 4A-9
LCRV (Load Conscious Reducing Valve) . . . 4A-12
Caution: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this
cable will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK
unless otherwise noted.
Type
Pedal Ratio
Pedal Stroke
Pedal Freeplay
Type
Inner Diameter
Type
Ratio
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
I.D. of Caliper Cylinder
Thickness of Brake Pad
Thickness of Disc Plate
Type
Operation
Specification
PBR Brake
4.3 : 1
132 mm
φ
23.81 mm
5.0 : 1
φ
60.4 mm
←
φ
40.5 mm
9.5 mm
←
Suspended
1 - 4 mm
Tandem Type with Lever Sensor
Vacuum Booster Type
Ventilated Disc
10 mm
24 mm
Rear Wheel Internal Expansion Type
Mechanical
SAE J1703, DOT3
SPECIFICATIONS
GENERAL SPECIFICATIONS
Brake Pedal
Master Cylinder
Brake Booster
Front Brake
Rear Brake
Parking Brake
Brake Fluid
MANDO Brake
4.3 : 1
138 mm
φ
25.4 mm
5.6 : 1
φ
60 mm
Solid Disc
φ
38.2 mm
10.0 mm
10.4 mm
Application
4A-2 HYDRAULIC BRAKES
Check
Dirty or Lack of Fluid
Air in Brake System
Faulty Brake Booster
Poor Contact of Pad or Lining
Oil or Grease on Pad
Faulty Auto Adjuster
Over Heated Rotor Due to Dragging Pad or Lining
Clogging Brake Line
Faulty Proportioning Valve
Check
Incorrect Tire Pressure Between Left and Right
Poor Contact of Pad or Lining
Oil or Grease is Applied to Pad or Lining
Bent or Uneven Wear of Drum
Incorrectly Mounted Wheel Cylinder
Faulty Auto Adjuster
Action
Repair
Retighten
Replace
Replace
Repair
Repair
Lubricate
Retighten
Check
Incorrectly Mounted Back Plate or Caliper
Loosened Bolt of Back Plate or Caliper
Crack or Uneven Wear of Brake Drum or Disc
Pad or Lining Sticking to Contact Surface
Excessive Clearance Between Caliper and Pad
Uneven Contact of Pad
Lack of Lubrication
Loosened Suspension
DIGNOSIS
NOISE OR VEHICLE VIBRATION WHEN APPLIED BRAKE
PULLS TO ONE SIDE WHEN BRAKING
Action
Adjust
Repair
Replace
Replace
Repair
Replace
Action
Replenish or Replace(Check eventual leakage)
Bleeding
Replace
Repair
Replace
Replace
Repair
Repair
Repair
POOR BRAKING
( If low cut-in : Adjust )
( If Leakage : Replace )
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст