SsangYong Musso. Manual — part 232
TIRES AND WHEELS 2E-5
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
WHEELS AND TIRES
Removal & Installation Procedure
1. Inspection of tire
Check tread area for tread surface, crack, damage by nail
in or stones. Replace or repair if necessary.
!
Replace the tire if tread-wear indicator of the tread
grooves appears where marked ' '
.
!
The wear limit of snow tire is the same as normal tire
(1.6mm) and indicator location is marked '
↓
'
.
Limit
1.6mm
Standard
2.66mm
Standard
2.03mm
2. Wear limit.
3. Runout measurement.
!
Excessive runout of tires and wheels can cause the
abnormal wear of tire. Using a dial indicator, measure
wheel and tire runout.
!
Measure radial runout at the rim flange and center of
the tire tread area.
!
Measure lateral runout at the tire bead area of the wheel
and tire sidewall.
Notice
If runout is excessive, replace the tire or wheel.
2E-6 TIRES AND WHEELS
4. Tire pressure inspection.
!
Tire pressure.
!
Check tread contact with road.
Notice
!
If underinflated, tire may come away from the wheel
during rapid steering.
!
An overinflated tire will cause a hard riding and uneven
wear.
Front & Rear
(P235/75R15)
2.1kg/cm (30PSI)
2
5. Wheel balance.
!
Balance weights should be on each side. When the wheel
is out of balance or a tire has been repaired, be sure to
balance the wheel again.
!
If total weight is over 150g, readjust the balance by
reinstalling the tire on the wheel.
!
Balance weight should not protrude from the wheel rim
over 3mm.
!
For aluminum wheel, use aluminum wheel balance weight
only.
TIRES AND WHEELS 2E-7
!
To correct unbalance, install equal weights 180° opposite
each other, one on the inside of the wheel and one on
the outside, at the point of unbalance.
!
Balance Weight
6. Cautions for installation and removal.
!
Clean the mounting surfaces of hub and wheel.
!
Do not apply grease or oil on the nuts and bolts (It will
cause looseness and poor tightening).
!
Using a jack, lift up the tire about 3cm from the ground.
!
Tighten nuts in a criss-cross pattern 2-3 times.
10g
0.4oz
20g
0.7oz
30g
1.10oz
40g
1.40oz
50g
1.80oz
60g
2.1oz
Steel : 80 - 120Nm
Aluminium : 110 - 130Nm
Tighten Torque
SECTION 1
ENGINE
SECTION 1A1(M162 ENGINE)
GENERAL ENGINE INFORMATION
Specifications . . . . . . . . . . . . . . . . . . . . . . . 1A1-1
Engine Specifications . . . . . . . . . . . . . . . . . . 1A1-1
Component Locator . . . . . . . . . . . . . . . . . . 1A1-3
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-3
Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-4
Performance Curve . . . . . . . . . . . . . . . . . . 1A1-5
E32 Engine . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-5
Special Tools . . . . . . . . . . . . . . . . . . . . . . . 1A1-6
Special Tools Table . . . . . . . . . . . . . . . . . . . . 1A1-6
Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . 1A1-7
Oil Leak Diagnosis . . . . . . . . . . . . . . . . . . . . 1A1-7
Engine Cranking at The
Front of Crankshaft . . . . . . . . . . . . . . . . . . 1A1-8
Compression Pressure Test . . . . . . . . . . . . . 1A1-9
Cylinder Pressure Leakage Test . . . . . . . . . 1A1-11
General Information . . . . . . . . . . . . . . . . . 1A1-13
Cleanliness and Care . . . . . . . . . . . . . . . . . 1A1-13
On-Engine Service . . . . . . . . . . . . . . . . . . . 1A1-13
Application
Engine Model
Displacement (CC)
Cylinder (Bore x Stroke) (mm)
Fuel Injection / Ignition System
Compression Ratio
Number of Cylinders
Camshaft Valve Arrangement
Camshaft Drive Type
Max. Output (ps/rpm)
Max. Torque (kg•m/rpm)
Firing Order
Ignition Type
Ignition Timing
Valve Timing
Intake
Open/Close
Exhaust
Open/Close
Valve Clearance Adjustment
SPECIFICATIONS
ENGINE SPECIFICATIONS
E32 Engine
M162.990
3199
89.9 x 84.0
MSE 3.62S
10 : 1
6
DOHC
Chain-Driven
222 / 5500
31.6 / 3750
1-5-3-6-2-4
Distributorless Double Ignition
BTDC 8° ± 2°
ATDC 11° / ABDC 34°
BBDC 31° / BTDC 14°
Automatic Control
TABLE OF CONTENTS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст