SsangYong Stavic / SsangYong Rodius (2005 year). Manual — part 234
41
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
Descriptions
Defective auto door lock opera-
tion
Defective door lock relay
Defective door unlock relay
Defective driver’s door unlock
relay
Defective wiper relay
Defective INT operation
Abnormal speed signal
Abnormal air bag collision signal
Abnormal door ajar warning light
signal
Abnormal air bag collision
sensor’s input signal
Abnormal air bag collision signal
Abnormal speed signal
Defective parking brake warning
light
Numbers of auto door lock fault
Numbers of door lock relay fault
Numbers of door unlock relay
fault
Numbers of driver’s door unlock
relay fault
Help
This DTC is set when the unit didn’t receive the contact signal of door
lock actuator after the unit has sent the “LOCK” signal to the door lock
relay (while the auto door lock is activated and the vehicle speed is
over 50 km/h).
This DTC is set when the unit didn’t receive the contact signal of door
lock actuator after the unit has sent the “LOCK” signal to the door lock
relay by the remote control key or knob.
This DTC is set when the unit didn’t receive the contact signal of door
unlock actuator after the unit has sent the “LOCK” signal to the door
unlock relay by the remote control key or knob.
This DTC is set when the unit didn’t receive the contact signal of door
unlock actuator after the unit has sent the “LOCK” signal to the door
unlock relay by the remote control key. (When the function that opens
driver’s door only is not operating)
This DTC is set when the wiper stop signal cannot be detected during
the wiper relay operation.
This DTC is set if the “OPEN” signal (4 V) is detected when changing
the INT VOLUME value (0 V: FAST, 4 V: SLOW) in vehicle speed
sensitive INT wiper equipped vehicle.
This DTC is set when more than 3 km/h of vehicle speed is detected
from the vehicle speed signal input area while the ignition key is in
“ON” position and ALT D is “LOW”.
The air bag unit receives the collision signal.
This DTC is set when the door lock actuator is locked in unlock condi-
tions after the collision signal is entered into collision sensor input end
in air bag unit.
This DTC is set when the door ajar warning light comes on while the
vehicle speed is over 3 km/h.
This DTC is set whenever the collision signal is entered into the colli-
sion sensor while the ignition key is in “OFF” position
This DTC is set when the STICS sends the door unlock signal and its
feedback value is normal.
This DTC is set when more than 200 km/h of vehicle speed is detected.
This DTC is set when the brake warning light comes on while the
vehicle speed is over 3 km/h.
Maximum numbers: 20 times
The number increases by 1 up to 20 when the fault is detected during
every IGN ON. It is reset to 0 when the DTC code is erased.
Maximum numbers: 20 times
The number increases by 1 up to 20 when the fault is detected during
every IGN ON. It is reset to 0 when the DTC code is erased.
Maximum numbers: 20 times
The number increases by 1 up to 20 when the fault is detected during
every IGN ON. It is reset to 0 when the DTC code is erased.
Maximum numbers: 20 times
The number increases by 1 up to 20 when the fault is detected during
every IGN ON. It is reset to 0 when the DTC code is erased.
Code
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
42
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RK STICS
STAVIC - 2004.09
2C
Removal and Installation of STICS
Preceding Work: Removal of driver side instrument panel undercover
1. Unscrew four bolts and remove the STICS unit.
2. Install in the reverse order of removal.
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RAIN SENSING WIPER
STAVIC - 2004.09
3
2D
RAIN SENSING WIPER
The rain sensing wiper unit in this vehicle doesn’t control the wiper directly. The rain sensing unit detects the amount of
rain drops and sends the operating signal to STICS, and STICS drives the wiper directly.
1. COMPONENTS
Rain sensing unit
Multifunction wiper switch:
AUTO and sensitivity control
ICM box
The wiper related relays are
installed in ICM box.
STICS
A sensor that emits infrared rays through LED
and then detects the amount of rain drops by
receiving reflected rays against sensing section
(rain sensor mounting section on the windshield)
with photodiode.
The rain sensing unit detects the amount of
rain drops and sends the operating signal to
STICS, and STICS drives the wiper directly.
At this moment, STICS determines the wiper
operation mode (washer, MIST, AUTO), then
sends the information to the rain sensor.
AUTO
: Wiper operates automatically by rain sensor
FAST <-------> SLOW
: Auto delay/Auto speed control. A position that
can control sensitivity against rains on the
windshield and transmits wiping demand
signal accordingly.
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
RAIN SENSING WIPER
STAVIC - 2004.09
4
2D
2. RAIN SENSOR OPERATION
The rain sensor is installed on the specific heat treated windshield that has minimum 13% of transmittance rate with
specified intensity of radiation. It is installed on the glass with a adhesive of Sorepa. It communicates with STICS and
makes the wipers to operate automatically under the rain sensing mode (multifunction switch wiper: AUTO mode). The
emitting section of the rain sensor unit emits infrared rays against the windshield and then detects the amount of rain
drops by receiving reflected rays with photodiode.
The sensing section on the windshield is located just above the center point between LED and photodiode.
Components and functions of the rain sensor unit
Rain sensor unit (including cover)
Front
Rear
Emitter lens
The LED emits the infrared
rays is located at bottom and
the lens guides the infrared
rays to target point.
Rain sensor
unit
PCB assembly and
emitter lens
Housing and
receiver lens
Unit latch
Housing and PCB
Receiver lens
The receiver lens guides the
reflected infrared rays from
windshield to photodiode.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст