SsangYong Rexton. Manual — part 114
DI10-61
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.4
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P0215
P1500
P0642
P0643
P0641
Main Relay Fault - Stuck
Vehicle Speed Fault
ECU Supply Voltage 1 Fault
- Low (5 V)
ECU Supply Voltage 1 Fault
- High (5 V)
ECU Supply Voltage 1 Fault
(5 V)
- The main relay is stuck ; Shut down.
- Resistance of main relay: 92
Ω ± 9 Ω
(at 20°C)
- Check the main relay wiring harness.
- Check the ECU wiring harness.
• Check the ECU pin #3, 4, 5 for open
and short.
- If the forced operation is not available,
replace the ECU.
- Check the fuse for main relay
- The vehicle speed signal through CAN
communication is faulty.
- Check the CAN communication line for
open and short.
- Check the ABS/ESP and TCU commu-
nication lines.
- Check the ECU wiring harness.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
DI10-62
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.4
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P0652
P0653
P0651
P0698
P0699
ECU Supply Voltage 2 Fault
- Low (5 V)
ECU Supply Voltage 2 Fault
- High (5 V)
ECU Supply Voltage 2 Fault
(5 V)
ECU Supply Voltage Fault -
Low (2.5 V)
ECU Supply Voltage Fault -
High (2.5 V)
O
O
O
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (5 V): accelerator
pedal sensor 1, HFM sensor, rail
pressure sensor, booster pressure
sensor, cam sensor
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 2.5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (2.5 V): accelerator
pedal sensor 2
- Check the wiring harnesses.
- Replace the ECU if required.
- Malfunction reference supply voltage
from ECU
• Supply voltage: 2.5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (2.55 V): accelera-
tor pedal sensor 2
- Check the wiring harnesses.
- Replace the ECU if required.
O
O
O
DI10-63
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.4
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P0697
P0245
P0246
P0606
P1607
P1600
P1601
P1602
ECU Supply Voltage Fault
(2.5 V)
Turbo Charger Actuator
Circuit Fault - Short
Turbo Charger Actuator
Circuit Fault - Short to B+
ECU Watchdog Fault
ECU Injector Cut Fault
ECU Shut Down Fault
ECU Fault
ECU Fault
O
O
- Malfunction reference supply voltage
from ECU
• Supply voltage: 2.5 V
- Check the supply voltage to each sen-
sor
• Supply voltage (2.55 V): accelera-
tor pedal sensor 2
- Check the wiring harnesses.
- Replace the ECU if required.
- The waste gate driver circuit is short
to ground or open
- Check the actuator wiring harness.
- Check the solenoid valve.
- Check the ECU wiring harness.
• Check the ECU pin #95 for open and
short.
- Replace the ECU if required.
- The turbo charger actuator power
source circuit is short.
- Check the actuator wiring harness.
- Check the solenoid valve.
- Check the ECU wiring harness for short
and poor contact.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
DI10-64
CHANGED BY
EFFECTIVE DATE
AFFECTED VIN
DIAGNOSIS
DI ENG SM - 2004.4
DTC
Trouble
Limp
Home
Mode
Immediately
Engine
Stop
Delayed
Engine
Stop
Torque
Reduction
(max.20%)
Help
Torque
Reduction
(max.50%)
P1614
P1615
P1616
P1606
P1620
P1621
P1622
P1603
P1604
P1605
P1148
ECU C2I/MDP Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
ECU Fault
Accelerometer (Knock
Sensor) Learning Fault
O
O
O
O
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- The ECU is defective.
- Check the chassis ground wiring
harness.
- Check the ECU.
- Replace the ECU if required.
- Check if the MDP is successful.
- Check the accelerometer (knock
sensor) sensor and wiring harness.
- Replace the ECU if required.
O
O
O
O
O
O
O
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст