Isuzu Trooper (2000 year). Manual — part 299
6E–325
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P0420 – TWC System Low Efficiency Bank 1
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to
Step 2
Go to
OBD
System
Check
2
Are any other DTCs set (such as P0140)?
—
Diagnose
other DTC(s)
first
Go to
Step 3
3
1. Visually and physically inspect the three-way
catalytic converter for damage. Check for the
following:
D
dents
D
severe discoloration caused by excessive
temperatures
D
holes
D
internal rattle caused by damaged catalyst
2. Also, ensure that the three-way catalytic converter
is a proper original equipment manufacturer part.
Did your inspection reveal a problem?
—
Go to
Step 6
Go to
Step 4
4
1. Visually and physically inspect the exhaust system
between the three-way catalytic converter and the
rear converter flange for leaks, damage, and loose
or missing hardware.
2. If a problem is found, repair as necessary.
Did your inspection reveal a problem?
—
Go to
Step 7
to verify
repair
Go to
Step 5
5
1. Visually and physically inspect the Bank 1 HO2S 2.
2. Ensure that the Bank 1 HO2S 2 is secure and that
the pigtail and wiring harness is not contacting the
exhaust pipe or is not otherwise damaged.
3. If a problem is found, repair as necessary.
Did your inspection reveal a problem?
—
Go to
Step 7
to verify
repair
Go to
Step 6
6
Replace the three-way catalytic converter.
NOTE: Check for conditions which may cause catalyst
damage (refer to
Diagnostic Aids).
Is the action complete?
—
Go to
Step 7
to verify
repair
—
7
1. Review and record the Tech 2 Failure Records data.
2. Clear DTC P0420.
3. Start the engine and allow it to warm up until the
engine coolant temperature monitored on the Tech
2 is above the specified value.
4. Run the engine to maintain the specified mass air
flow range for at least 2 minutes.
5. Operate the vehicle to maintain DTC P0420 test
conditions (refer to
DTC Test Description in
Diagnostic Support for detailed instructions).
6. Using a Tech 2, monitor “DTC” info for DTC P0420
until the DTC P0420 test runs.
7. Note the test result.
Does the Tech 2 indicate DTC P0420 passed this
ignition?
Engine
coolant temp:
greater than
60
°
C
(140
°
F).
Mass air flow:
between 8
g/second and
50 g/second
Repair
complete. If
a driveability
symptom still
exists, refer
to
Symptoms.
Go to the
Diagnostic
Aids
6E–326
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Trouble Code (DTC) P0430 TWC System Low Efficiency Bank 2
T321075
Circuit Description
To control emissions of hydrocarbons (HC), carbon
monoxide (CO), and oxides of nitrogen (NOx), a
three-way catalyst (TWC) is used. The catalyst promotes
a chemical reaction which oxidizes the HC and CO
present in the exhaust gas, converting them into
harmless water vapor and carbon dioxide. The catalyst
also reduces NOx, converting it to nitrogen. The
powertrain control module (PCM) has the ability to
monitor this process using the Bank 2 HO2S 1 and the
Bank 2 HO2S 2 heated oxygen sensors. The Bank 2
HO2S 1 sensor produces an output signal which indicates
the amount of oxygen present in the exhaust gas entering
the three-way catalytic converter. The Bank 2 HO2S 2
sensor produces an output signal which indicates the
oxygen storage capacity of the catalyst; this in turn
indicates the catalyst’s ability to convert exhaust gases
efficiently. If the catalyst is operating efficiently, the Bank
2 HO2S 1 signal will be far more active than that produced
by the Bank 2 HO2S 2 sensor. If the PCM detects a level
of Bank 2 HO2S 2 activity that indicates the catalyst is no
longer operating efficiently, DTC P0430 will be set.
Conditions for Setting the DTC
D
No related DTCs.
D
The engine is operating in “closed loop.”
D
Engine air load is below 99%.
D
Engine coolant temperature is between 70
°
C (158
°
F)
and 115
°
C (239
°
F).
D
Mass air flow is between 2.5 g/second and 10
g/second.
D
Change in engine load is below 8%.
D
Engine speed is below 200 RPM.
D
Catalyst temperature is above 350
°
C (662
°
F).
D
The PCM determines that the catalyst’s oxygen
storage capacity is below the acceptable threshold.
D
Intake Air temperature is between –20
°
C (4
°
F) and
70
°
C (158
°
F).
Action Taken When the DTC Sets
D
The PCM will illuminate the malfunction indicator lamp
(MIL) the first time the fault is detected.
D
The PCM will store conditions which were present
when the DTC was set as Freeze Frame and in the
Failure Records data.
Conditions for Clearing the MIL/DTC
D
The PCM will turn the MIL “OFF” on the third
consecutive trip cycle during which the diagnostic has
been run and the fault condition is no longer present.
D
A history DTC P0430 will clear after 40 consecutive
warm-up cycles have occurred without a fault.
D
DTC P0430 can be cleared by using the Tech 2 “Clear
Info” function or by disconnecting the PCM battery
feed.
6E–327
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
Diagnostic Aids
Check for the following conditions:
D
Poor connection at PCM – Inspect harness connectors
for backed-out terminals, improper mating, broken
locks, improperly formed or damaged terminals, and
poor terminal-to-wire connection.
D
Damaged harness – Inspect the wiring harness for
damage. If the harness appears to be OK, observe the
display on the Tech 2 while moving connectors and
wiring harnesses related to the sensor. A change in the
display will indicate the location of the fault.
Reviewing the Failure Records vehicle mileage since the
diagnostic test last failed may help determine how often
the condition that caused the DTC to be set occurs. This
may assist in diagnosing the condition.
Test Description
Number(s) below refer to the step number(s) on the
Diagnostic Chart.
7. Difficulty completing the DTC P0430 “Status This
Ign.” test may be encountered in areas where test
conditions cannot be maintained easily, especially in
urban areas. To minimize the amount of driving
required to complete the DTC P0430 “Status This
Ign.” test, use the following procedure:
D
Allow the engine to warm completely.
D
With the vehicle in “Park,” monitor mass air flow on
the Tech 2 and hold part throttle to maintain a
reading of over 12 g/second for at least 2 minutes.
This will achieve the “warm catalyst” required for
running the test.
D
Operate the vehicle in second or third gear to remain
in the DTC P0430 test conditions described in
“Conditions for Setting the DTC” as much as
possible. If you must stop the vehicle, maintain the
“warm catalyst” criteria as follows:
– Place the vehicle in “Park” or “Neutral.”
– Hold part throttle to maintain a mass air flow
reading of over 15 g/second for the duration of the
stop.
The “TWC Monitor Test Counter” displayed on the Tech 2
may be used to monitor the progress of the TWC
diagnostic. To complete the TWC diagnostic with a good
catalyst, the counter must be allowed to increment to 49
samples and roll over to 0 at least twice.
6E–328
TROOPER 6VE1 3.5L ENGINE DRIVEABILITY AND EMISSIONS
DTC P0430 – TWC System Low Efficiency Bank 2
Step
Action
Value(s)
Yes
No
1
Was the “On-Board Diagnostic (OBD) System Check”
performed?
—
Go to
Step 2
Go to
OBD
System
Check
2
Are any other DTCs set (such as P0160)?
—
Diagnose
other DTC(s)
first
Go to
Step 3
3
1. Visually and physically inspect the three-way
catalytic converter for damage. Check for the
following:
D
dents
D
severe discoloration caused by excessive
temperatures
D
holes
D
internal rattle caused by damaged catalyst
2. Also, ensure that the three-way catalytic converter
is a proper original equipment manufacturer part.
Did your inspection reveal a problem?
—
Go to
Step 6
Go to
Step 4
4
1. Visually and physically inspect the exhaust system
between the three-way catalytic converter and the
rear converter flange for leaks, damage, and loose
or missing hardware.
2. If a problem is found, repair as necessary.
Did your inspection reveal a problem?
—
Go to
Step 7
to verify
repair
Go to
Step 5
5
1. Visually and physically inspect the Bank 2 HO2S 2.
2. Ensure that the Bank 2 HO2S 2 is secure and that
the pigtail and wiring harness is not contacting the
exhaust pipe or is not otherwise damaged.
3. If a problem is found, repair as necessary.
Did your inspection reveal a problem?
—
Go to
Step 7
to verify
repair
Go to
Step 6
6
Replace the three-way catalytic converter.
NOTE: Check for conditions which may cause catalyst
damage (refer to
Diagnostic Aids).
Is the action complete?
—
Go to
Step 7
to verify
repair
—
7
1. Review and record the Tech 2 Failure Records data.
2. Clear DTC P0430.
3. Start the engine and allow it to warm up until the
engine coolant temperature monitored on the Tech
2 is above the specified value.
4. Run the engine to maintain the specified mass air
flow range for at least 6 minutes.
5. Operate the vehicle to maintain DTC P0430 test
conditions (refer to
DTC Test Description in
Diagnostic Support for detailed instructions).
6. Using a Tech 2, monitor “DTC” info for DTC P0430
until the DTC P0430 test runs.
7. Note the test result.
Does the Tech 2 indicate DTC P0430 passed this
ignition?
Engine
coolant temp:
greater than
70
°
C
(158
°
F).
Mass air flow:
between 2.5
g/second and
10 g/second
Repair
complete. If
a driveability
symptom still
exists, refer
to
Symptoms.
Go to the
Diagnostic
Aids
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст