Isuzu Trooper (2000 year). Manual — part 63
3C 17
FRONT SUSPENSION
7. Install the camber shims(1) between the chassis
frame and fulcrum pin.
450RS014
8. Install nut assembly.
9. Install bolt and plate, then tighten the bolt to the
specified torque.
Torque: 152 N·m (112 lb ft)
10. Install upper ball joint and tighten it to the specified
torque.
Torque: 57 N·m (42 lb ft)
11. Install nut and cotter pin then tighten the nut to the
specified torque, with just enough additional torque to
align cotter pin holes. Install new cotter pin.
Torque: 98 N·m (72 lb ft)
12. Install speed sensor cable.
3C 18
FRONT SUSPENSION
Lower Control Arm
Lower Control Arm and Associated Parts
450RS015
Legend
(1) Nut and Washer, Front
(2) Bush, Front
(3) Bolt, Front
(4) Nut and Washer, Rear
(5) Bush, Rear
(6) Bolt, Rear
(7) Bolt, Lower Ball Joint
(8) Bolt, Torsion Bar Arm
(9) Torsion Bar Arm Bracket
(10) Torsion Bar
(11) Lower Control Arm
(12) Lower Ball Joint
(13) Shock Absorber
(14) Stabilizer Link
Removal
1. Raise the vehicle and support the frame with suitable
safety stands.
2. Remove wheel and tire assembly. Refer to Wheel
Replacement in this section.
3. Remove the outer track rod from the knuckle. Refer to
Steering Linkage in Steering section.
4. Remove the retaining ring from the front axle driving
shaft to release the shaft from hub. Refer to Front Hub
and Disc in Driveline/Axle section.
5. Support lower control arm with a jack.
6. Remove front nut and washer.
3C 19
FRONT SUSPENSION
7. Remove rear nut and washer.
8. Remove torsion bar, refer to Torsion Bar
Replacement in this section.
9. Remove torsion bar arm bracket.
10. Disconnect the stabilizer link at the lower control arm.
11. Remove the shock absorber lower end from the lower
control arm.
12. Remove the lower ball joint from the lower control
arm.
13. Remove front bolt.
14. Remove rear bolt.
15. Remove lower control arm.
16. Remove torsion bar arm bolt.
17. Remove lower ball joint bolt.
18. Remove front bushing by using remover J–36833.
901RW034
901RW035
19. Remove rear bushing by using remover J–36834.
901RW051
3C 20
FRONT SUSPENSION
901RW052
Inspection and Repair
Make necessary correction or parts replacement if wear,
damage, corrosion or any other abnormal conditions are
found through inspection.
Check the following parts:
D
Lower control arm
D
Bushing
Installation
1. Install rear bushing by using installer J–36834.
901RW053
2. Install front bushing by using installer J–36833.
901RW036
3. Install lower ball joint bolt.
4. Install torsion bar arm bolt.
5. Install lower control arm.
6. Install rear bolt.
7. Install front bolt.
8. Install lower ball joint and tighten it to the specified
torque.
Torque: 103 N·m (76 lb ft)
9. Install shock absorber and tighten it to the specified
torque.
Torque: 82 N·m (61 lb ft)
10. Install stabilizer link and tighten it to the specified
torque.
Torque: 50 N·m (37 lb ft)
11. Install torsion bar arm bracket and tighten it to the
specified torque.
Torque: 116 N·m (85 lb ft)
12. Install Torsion bar, refer to Torsion Bar Replacement
in this section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст