Isuzu Trooper (2000 year). Manual — part 462
8E–8
METER AND GAUGE
Meter Assembly W/TOD–1
825RW035
METER AND GAUGE
8E–9
Meter Assembly W/TOD–2
Connector No. I–9
Terminal
Function
1
—
2
Air bag warning light
3
A/T oil temp warning light
4
Charge warning light
5
Seat belt warning switch
6
Check trans warning light
7
Brake warning light
8
—
9
Tachometer
10
—
11
Turn signal indicator light (Left)
12
A/T shift indicator control unit
13
2 position (A/T)
14
D position (A/T)
15
Rear (TOD)
16
Auto (TOD)
17
Check (TOD)
18
Cruise set indicator light
19
Cruise main indicator light
20
Oil pressure warning light
21
Front “1” (TOD)
22
Front “2” (TOD)
23
Front “3” (TOD)
24
Lighting switch
25
Illumination controller
26
Starter switch
27
—
28
Winter drive indicator light
29
Power drive indicator light
30
—
Connector No. I–10
Terminal
Function
1
Turn signal indicator light (Right)
2
L position (A/T)
3
R position (A/T)
4
Check engine warning light
5
Speedometer
6
—
7
—
8
Battery (+)
9
Engine coolant temperature gauge
10
Ground (Warning)
11
P position (A/T)
12
N position (A/T)
13
3 position (A/T)
14
High beam indicator light (–)
15
High beam indicator light (+)
16
ABS indicator light
17
—
18
Fuel warning light
19
—
20
Fuel gauge
21
Ground (Gauge)
22
—
8E–10 METER AND GAUGE
Removal
1. Disconnect the battery ground cable.
2. Remove the front console assembly(1).
Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cluster assembly(2).
Refer to the Instrument Panel Assembly in Body
Structure section.
4. Remove the instrument panel driver lower cover(3).
Refer to the Instrument Panel Assembly in Body
Structure section.
740RS004
5. Remove four fixing screws and disconnect the meter
connectors to remove the meter assembly(5).
825RW031
CAUTION: The removed meter assembly should be
placed upright or with its face side up.
Installation
To install, follow the removal steps in the reverse order.
Warning Light Bulb, Indicator Light Bulb, Illumination Light Bulb,
A/T Indicator Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the meter assembly(1).
Refer to the Meter Assembly removal steps in this
section.
3. Hold the bulb socket by hand and rotate it
counterclockwise to remove the socket & bulb(2)
from the meter body.
825RW032
Installation
To install, follow the removal steps in the reverse order.
METER AND GAUGE
8E–11
Vehicle Speed Sensor
Removal
1. Disconnect the battery ground cable.
2. Disconnect the connector, remove the vehicle speed
sensor body by rotating it and then remove the vehicle
speed sensor(1).
826RS009
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1. Tighten the vehicle speed sensor to the specified
torque.
Torque: 27 N·m (20 lb ft)
Fuel Tank Unit
Removal
1. Disconnect the battery ground cable.
2. Remove the fuel tank(1).
Refer to the Fuel Tank removal steps in Engine
section
3. Disconnect the connectors, remove five screws and
then remove the fuel tank unit(2).
140RS006
Installation
To install, follow the removal steps in the reverse order.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст