Isuzu Trooper (2000 year). Manual — part 69
3D–14
REAR SUSPENSION
Main Data and Specifications
General Specifications
Rear suspension
Type
4–Link, coil spring type with stabilizer bar.
Coil spring
Free length
402mm (15.83in)
Spring diameter
12.7mm (0.5in)
Coil diameter (inner)
105mm (4.13in)
Effective No. of turns
5.32
Total No. of turns
6.82
Shock absorber
Type
Hydraulic, double acting, telescopic
Piston diameter
25.0mm (0.98in)
Stroke
175mm (6.89in)
Extended length
489mm (19.25in)
Compressed length
314mm (12.36in)
Stabilizer bar
Diameter
19.0mm (0.75in)
3D–15
REAR SUSPENSION
Torque Specifications
E03RW006
3D–16
REAR SUSPENSION
Special Tools
ILLUSTRATION
TOOL NO.
TOOL NAME
J–39214
Remover and Installer;
Trailing center link
bushing
J–39792
Remover and Installer;
Lateral rod bushing (axle
side)
J–39215
Remover and Installer;
Lateral rod bushing
3E–1
WHEEL AND TIRE SYSTEM
TROOPER
SUSPENSION
WHEEL AND TIRE SYSTEM
CONTENTS
Service Precaution
3E–1
. . . . . . . . . . . . . . . . . . . . . .
General Description
3E–2
. . . . . . . . . . . . . . . . . . . . .
Diagnosis
3E–3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel
3E–9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel and Associated Parts
3E–9
. . . . . . . . . . . .
Removal
3E–9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation
3E–9
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire
3E–10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tire Replacement
3E–10
. . . . . . . . . . . . . . . . . . . . . .
General Balance Procedure
3E–10
. . . . . . . . . . . . . .
Balancing Wheel and Tire
3E–11
. . . . . . . . . . . . . . . .
Main Data and Specifications
3E–12
. . . . . . . . . . . . .
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNING COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fastener. When
you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст